The 2015 Subaru Impreza Sedan is a popular choice for drivers who value reliability, safety, and performance. One of the features that sets the Impreza apart from its competitors is its standard rearview camera. This camera provides a clear view of the area behind the vehicle, making it easier to reverse and park. However, there may come a time when you need to replace the rearview camera. This can be a daunting task, but it is actually quite simple to do with the right tools and instructions.
To remove the old camera, you will need a Phillips head screwdriver and a trim removal tool. Begin by removing the two screws that are located on the top of the camera housing. Next, use the trim removal tool to carefully pry the housing away from the body of the vehicle. Once the housing is removed, you will need to disconnect the electrical connector from the back of the camera. Finally, remove the two screws that are located on the sides of the camera and lift the camera out of the housing.
Once the old camera is removed, you can install the new camera by reversing the steps that you followed to remove the old camera. Be sure to tighten all of the screws securely and reconnect the electrical connector. Once the new camera is installed, test it to make sure that it is working properly. If you have any questions about how to remove the old camera or install the new camera, please consult a qualified mechanic.
Preparing the Work Area
Before you begin removing the old camera, it’s important to properly prepare your work area. This will help ensure a safe and efficient process.
Here are the steps involved in preparing the work area:
- Clear a spacious and well-lit workspace: Choose a clean and well-ventilated area where you have ample room to maneuver. Ensure you have adequate lighting to see clearly during the disassembly process.
- Gather necessary tools: You will need a set of screwdrivers (Phillips and flathead), a socket wrench with appropriate sockets, and a trim removal tool (optional). Make sure all tools are in good condition and appropriate for the task.
- Protect the vehicle’s exterior: Cover the areas around the camera with painter’s tape or a soft cloth to prevent scratches or damage during disassembly.
- Disconnect the battery: For safety, disconnect the negative terminal of the vehicle’s battery before proceeding with disassembly. This will prevent any electrical shorts or malfunction.
| Tool | Purpose |
|---|---|
| Phillips Screwdriver | Removing screws |
| Flathead Screwdriver | Prying off trim panels |
| Socket Wrench | Removing bolts |
| Trim Removal Tool | Safely removing interior trim panels |
Identifying the Old Camera Location
Locating the old camera in your 2015 Subaru Impreza Sedan is straightforward. Here’s a step-by-step guide:
Step 1: Pinpoint the Camera’s Location
The rearview camera is typically situated in the center of the vehicle’s rear bumper. Refer to your Impreza Sedan’s owner’s manual or consult a mechanic to confirm its precise location if necessary.
Step 2: Examine the Camera Housing
Once the camera’s location has been identified, examine the housing that encloses it. You’ll notice a sturdy plastic cover that shields the camera from external elements. This cover is usually secured by a combination of clips or bolts.
Removing the Camera Housing
To remove the housing, follow these steps:
| Step | Action |
|---|---|
| 1. | Carefully pry off any clips holding the housing in place using a flat-head screwdriver or a trim removal tool. |
| 2. | If bolts are present, use a wrench or socket to remove them gently. |
| 3. | Once the housing is detached, handle it with caution to avoid damaging the camera. |
Disconnecting the Old Camera
To disconnect the old camera, you will need to follow these steps:
- Locate the camera module. It is usually located in the rear of the vehicle, near the license plate.
- Disconnect the electrical connector from the camera module. The connector is usually located on the side of the camera module.
- Unscrew the mounting bolts that hold the camera module in place. There are usually two or three mounting bolts.
Note: Be careful not to drop the camera module when you remove the mounting bolts.
- Remove the camera module from the vehicle.
- Check the connection: Make sure that the camera is securely connected to the wiring harness. Wiggle the connector to see if it becomes loose.
- Check the fuse: The camera fuse is located in the fuse box, which is usually under the hood of the car. Check the fuse to see if it has blown and replace it if necessary.
- Check the wiring: Inspect the wiring harness for any damage, such as cuts or breaks. If you find any damage, repair or replace the wiring.
- Clean the lens: The camera lens can become dirty over time, which can affect its performance. Use a soft cloth to carefully clean the lens.
- Verify the camera settings: Make sure that the camera settings are correct, such as the brightness and contrast. You can usually access the camera settings through the car’s infotainment system.
- Contact a professional: If you’ve tried all of the above troubleshooting steps and the camera is still not working, you may need to contact a professional for assistance.
- Carefully insert the new camera into the designated space, ensuring it aligns correctly.
- Secure the camera using the screws or other fasteners provided.
- Reconnect all electrical wires, cables, and harnesses to the new camera.
- Inspect the connections to ensure they are firm and reliable.
- Reassemble any removed panels, covers, or trim pieces.
- Check that all components are securely fastened and in their original positions.
- Tighten any loose screws or bolts.
- Clean up the work area, removing any debris or loose parts.
- Disconnect the negative battery terminal.
- Wait at least 10 minutes before reconnecting the negative battery terminal. This allows the electrical systems to reset properly.
- Check the camera’s functionality by turning on the ignition and engaging the reverse gear.
- Ensure that the camera displays a clear and unobstructed image.
- Take your time and double-check all connections before reassembling the work area.
- If you encounter any difficulties or uncertainties, refer to the vehicle’s service manual or consult a qualified technician.
- Open the trunk and locate the camera.
- Disconnect the electrical connector by pressing the release button and pulling the connector straight out.
- Remove the two screws that secure the camera to the trunk lid.
- Carefully pull the camera straight out of the trunk lid.
- Insert the new camera into the trunk lid.
- Secure the camera with the two screws.
- Connect the electrical connector.
- Close the trunk.
Things to Keep in Mind:
Here are a few things to keep in mind when disconnecting the old camera:
| Tip | Description |
|---|---|
| Make sure that the vehicle is parked in a safe location and that the parking brake is engaged. | This will help to prevent the vehicle from moving while you are working on it. |
| Disconnect the negative battery terminal before starting any electrical work. | This will help to prevent electrical shock. |
| Use a torque wrench to tighten the mounting bolts to the specified torque. | This will help to prevent the bolts from becoming loose and the camera module from falling off. |
Removing the Camera Mounting Screws
Before you can remove the old camera, you’ll need to remove the screws that are holding it in place. These screws are typically located on the side or back of the camera.
To remove the screws, you’ll need a Phillips head screwdriver. Once you have the screwdriver, insert it into the screw and turn it counterclockwise. Be careful not to over-tighten the screws, as this can damage the camera.
Once the screws are removed, you can carefully pull the camera away from the mounting bracket.
Using a Screwdriver
If you have a screwdriver that fits the screws, you can use it to remove them. Simply insert the screwdriver into the screw and turn it counterclockwise. Be careful not to over-tighten the screws, as this can damage the camera.
Using a Wrench
If you don’t have a screwdriver that fits the screws, you can use a wrench. To do this, insert the wrench over the screw and turn it counterclockwise. Be careful not to over-tighten the screws, as this can damage the camera.
Using a Socket Wrench
If you have a socket wrench, you can use it to remove the screws. To do this, insert the socket over the screw and turn it counterclockwise. Be careful not to over-tighten the screws, as this can damage the camera.
Extracting the Old Camera Unit
To remove the old camera unit from your 2015 Subaru Impreza Sedan, follow these steps:
1. Disconnect the battery
First, disconnect the negative terminal of your battery to prevent any electrical shorts. Use a wrench to loosen the bolt holding the terminal in place, then carefully pull the terminal off the battery.
2. Locate the camera unit
The camera unit is located behind the rear bumper. To access it, you will need to remove the bumper cover. Refer to your vehicle’s repair manual for instructions on how to do this.
3. Remove the camera unit
Once the bumper cover is removed, you can see the camera unit mounted on the rear bumper reinforcement. Disconnect the electrical connector to the camera unit and then use a wrench or socket to remove the bolts holding the camera unit in place.
4. Remove the camera lens
After removing the bolts, you can remove the camera lens by gently pulling it out of the camera housing. Hold the lens by the edges to avoid touching the glass surface.
5. Detach the camera housing
To detach the camera housing from the bumper reinforcement, you will need to remove several clips and bolts. Carefully separate the housing from the reinforcement and disconnect any remaining electrical connectors.
| Clip Location | Bolt Size |
|---|---|
| Top of Housing | 10mm |
| Bottom of Housing | 12mm |
| Left Side of Housing | 8mm |
| Right Side of Housing | 8mm |
Replacing the Old Camera
Replacing the outdated camera in your 2015 Subaru Impreza Sedan involves a straightforward process. Here’s a detailed guide to assist you:
1. Gather Necessary Materials
Before starting, gather the following items: a new camera, a Phillips head screwdriver, a flathead screwdriver, and a trim removal tool.
2. Disconnect the Battery
For safety, disconnect the negative terminal of the battery to prevent any electrical shorts.
3. Remove the Trunk Trim
Use the trim removal tool to gently pry off the trunk trim surrounding the camera.
4. Locate the Camera Module
Once the trim is removed, locate the camera module attached to the trunk. It’s usually positioned in the center.
5. Disconnect the Camera
Unplug the electrical connector from the back of the camera module.
6. Removing the Camera Screw
Locate the screw that secures the camera module to the trunk. Use the Phillips head screwdriver to unscrew it. The screw is typically located in the center of the module. Gently lift the camera module out of its housing once the screw is removed.
Caution:
Avoid touching the camera lens during the removal process to prevent damage.
Tip:
If you encounter difficulties removing the screw, use a penetrating lubricant spray to loosen it.
Opening the Trunk
Locate the trunk release lever inside the vehicle and pull it to open the trunk.
Removing the Trunk Liner
Pull up on the trunk liner to release the clips holding it in place. Remove the liner and set it aside.
Finding the Camera Cable
Locate the camera cable connected to the back of the camera. It is usually a small, round black cable.
Unplugging the Camera
Gently pull the camera cable out of the connector on the back of the camera.
Removing the Camera Unit
Unscrew the two screws holding the camera unit in place using a Phillips head screwdriver. Pull the camera unit straight out of its housing.
Installing the New Camera
Insert the new camera unit into the housing and tighten the two screws to secure it.
Connecting the New Camera
Insert the new camera cable into the connector on the back of the camera. Push until you hear a click.
Here is a table summarizing the steps:
| Step | Description |
|---|---|
| 1 | Open the trunk. |
| 2 | Remove the trunk liner. |
| 3 | Find the camera cable. |
| 4 | Unplug the camera. |
| 5 | Remove the camera unit. |
| 6 | Install the new camera. |
| 7 | Connect the new camera. |
Reinstall the trunk liner and close the trunk.
Tightening the Camera Mounting Screws
Once the nuts are tightened, use a torque wrench to tighten the camera mounting screws. The torque specifications for the camera mounting screws are as follows:
Note: Be careful not to overtighten the camera mounting screws, as this could damage the camera.
| Screw Size | Torque Specification |
|---|---|
| M3 | 5.3 lb-in (0.6 Nm) |
| M4 | 9.5 lb-in (1.1 Nm) |
| M5 | 15.9 lb-in (1.8 Nm) |
| M6 | 23.6 lb-in (2.7 Nm) |
| M8 | 36.9 lb-in (4.2 Nm) |
To tighten the camera mounting screws, follow these steps:
1. Insert the torque wrench into the screw head.
2. Turn the torque wrench clockwise until the desired torque is reached.
3. Once the desired torque is reached, stop turning the torque wrench.
4. Repeat steps 1-3 for the remaining camera mounting screws.
Testing the New Camera
Once you’ve installed the new camera, you’ll need to test it to make sure it’s working properly. To do this, start the car and put the gear selector into drive. Then, look at the monitor to see if you can see the image from the camera. If you can’t see the image, check the following:
9. Troubleshooting Camera Issues
If you’re experiencing issues with your new camera, here are a few things you can try:
| Camera Issue | Possible Cause |
|---|---|
| No image on monitor | Loose connection, blown fuse, damaged wiring |
| Grainy or distorted image | Dirty lens, incorrect camera settings |
Reassembling the Work Area
With the old camera successfully removed, it’s time to reassemble the work area. Here’s a detailed guide to help you complete this task:
Additional Tips:
How to Remove the Old Camera from a 2015 Subaru Impreza Sedan
To remove the old camera from a 2015 Subaru Impreza Sedan, follow these steps:
People Also Ask
How do I replace the old camera with a new one?
To replace the old camera with a new one, follow these steps:
Where is the camera located on a 2015 Subaru Impreza Sedan?
The camera is located in the center of the trunk lid, behind the Subaru logo.
What tools do I need to remove the old camera?
You will need a Phillips head screwdriver.
