**How to Set the Clock on a 2009 Harley-Davidson Ultra Classic**
The 2009 Harley-Davidson Ultra Classic is a popular motorcycle that features a variety of amenities, including a digital clock. Setting the clock is a simple process that can be completed in just a few minutes. However, if you don’t have the owner’s manual, you may be wondering how to do it. Here are the steps on how to set the clock on a 2009 Harley-Davidson Ultra Classic without a title:
First, locate the clock on the motorcycle. It is located on the instrument panel, between the speedometer and tachometer. Once you have found the clock, press and hold the “Mode” button until the time starts to flash. Use the “Up” and “Down” buttons to adjust the hour and minute. Once you have set the time, press the “Mode” button again to save the changes. The clock will now display the correct time.
Accessing the Instrument Cluster
To access the instrument cluster, follow these steps:
1. Locate the instrument cluster, which is typically mounted on the handlebars.
2. Press and hold the “MODE” button on the cluster until the display shows the “Time” option.
3. Release the “MODE” button and press the “SET” button to enter time-setting mode.
4. Press the “HOUR” and “MIN” buttons to adjust the time.
| Button | Function |
|---|---|
| Mode | Scrolls through display options (e.g., time, mileage, fuel) |
| Set | Confirms selected option or enters time-setting mode |
| Hour | Adjusts the hour in time-setting mode |
| Min | Adjusts the minutes in time-setting mode |
5. Press the “MODE” button again to save the new time and return to the normal display.
Identifying the Clock Adjustment Buttons
The 2009 Harley Ultra Classic features an easy-to-use clock adjustment system. To locate the adjustment buttons, first identify the instrument cluster on the motorcycle’s dashboard. This cluster houses the speedometer, tachometer, and other vital gauges.
On the right-hand side of the instrument cluster, you will find two small buttons labeled “MODE” and “SET”. These buttons serve as the controls for adjusting the clock and other important settings.
To begin adjusting the clock, press and hold the “MODE” button until the clock display begins to flash. This indicates that the clock is now in adjustment mode.
Next, use the “SET” button to increment or decrement the time. Each press of the button will increase or decrease the time by one minute. Hold down the “SET” button to quickly advance or rewind the time.
Once you have adjusted the time to your desired setting, release the “SET” button. The clock will automatically save the new time and exit adjustment mode.
If you need to adjust the time again, simply repeat the above steps. The Harley Ultra Classic’s clock adjustment system is designed to be user-friendly and straightforward, ensuring that you can always keep track of the time while riding.
Setting the Time
Setting the Clock Display Mode
The first step is to set the clock display mode to 12-hour or 24-hour format. To do this, press and hold the “Mode” button for 3 seconds. Use the “Adj” knob to select the desired format and press the “Mode” button to confirm.
Adjusting the Hour
Press and hold the “Adj” knob for 3 seconds to enter time adjustment mode. The hour digits will start flashing. Use the “Adj” knob to adjust the hours by scrolling through the numbers. Once the correct hour is displayed, release the “Adj” knob.
Adjusting the Minutes
After adjusting the hour, the minute digits will start flashing. Use the “Adj” knob to adjust the minutes by scrolling through the numbers. Release the “Adj” knob when the correct minutes are displayed.
Example of Setting the Time
Suppose you want to set the time to 10:15 AM. Follow these steps:
| Step | Action |
|---|---|
| 1 | Press and hold “Mode” for 3 seconds. |
| 2 | Use the “Adj” knob to select “12 Hour” format. |
| 3 | Press “Mode” to confirm. |
| 4 | Press and hold “Adj” for 3 seconds. |
| 5 | Turn the “Adj” knob to set the hour to 10. |
| 6 | Turn the “Adj” knob to set the minutes to 15. |
| 7 | Release the “Adj” knob to save the time. |
Setting the Clock
- Use the MODE button on the left handlebar to navigate to the Clock setting.
- Press the SELECT button to access the Clock menu.
- Use the UP and DOWN buttons to adjust the hour.
- Press the SELECT button to confirm the hour setting.
- Use the UP and DOWN buttons to adjust the minutes.
- Press the SELECT button to confirm the minute setting.
Saving the Settings
1. Press the MODE button to exit the Clock menu.
2. Wait for the clock to display the correct time.
3. The settings will be automatically saved.
**Note:** If you do not wait for the clock to display the correct time before exiting the Clock menu, the settings will not be saved.
Troubleshooting
* If the clock is not displaying the correct time, check the battery connection.
* If the clock is not responding to button presses, try resetting the unit.
Additional Information
* The clock can be set to either a 12-hour or 24-hour format.
* The clock can be set to either display the time in hours and minutes or in hours, minutes, and seconds.
* The clock can be set to either use the AM/PM format or the 24-hour format.
Ensuring Clock Accuracy
To ensure the clock on your 2009 Harley Ultra Classic remains accurate, follow these steps:
1. Syncing System Time with GPS
The Ultra Classic’s clock can sync automatically with the GPS signal, providing high accuracy. Ensure the GPS antenna is active and connected.
2. Manual Adjustment
If GPS is unavailable, you can set the clock manually. Use the “Clock” menu on the instrument cluster to adjust hours, minutes, and seconds.
3. Maintaining Battery Power
A weak battery can disrupt clock accuracy. Replace the battery as needed or connect the bike to a battery tender when not in use for extended periods.
4. Checking Antenna Connection
Verify that the GPS antenna is securely connected to the bike’s electrical system. A loose connection can compromise signal reception.
5. Calibrating GPS
If GPS accuracy remains compromised, perform a GPS calibration. Consult your bike’s owner’s manual for specific instructions.
6. Checking For Interference
Electromagnetic interference from other devices can affect GPS signals. Position the bike away from potential sources of interference, such as construction sites or power lines.
7. Updating Firmware
Software updates may improve GPS signal reception and clock accuracy. Check with your Harley-Davidson dealer for available firmware updates.
8. Troubleshooting Persistent Inaccuracy
If you consistently experience clock inaccuracy even after following these steps, consider the following:
| Possible Cause | Solution |
|---|---|
| Faulty GPS antenna | Inspect the antenna for damage or loose connections. Replace if necessary. |
| Malfunctioning instrument cluster | Consult your Harley-Davidson dealer for diagnosis and repair. |
| Damaged electrical wiring | Check for any visible damage to wires connected to the GPS antenna or instrument cluster. Repair or replace as needed. |
Resetting the Clock
To reset the clock, simply press and hold the “Mode” button for about 5 seconds. The clock will then reset to 12:00 PM.
Setting the Hour
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “Hour” or “Min” button to adjust the hour.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
Setting the Minute
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “Min” button to adjust the minute.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
Setting the AM/PM Indicator
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “AM/PM” button to toggle between AM and PM.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
Setting the 12/24-Hour Format
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “12/24” button to toggle between the 12-hour and 24-hour format.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
Setting the Date
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “Date” button to adjust the date.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
Setting the Month
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “Month” button to adjust the month.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
Setting the Year
1. Press the “Mode” button to enter the clock setting mode.
2. Press the “Year” button to adjust the year.
3. Press the “Mode” button to save the changes and exit the clock setting mode.
How to Set Clock on 2009 Harley Ultra Classic
These easy steps will guide you through setting the clock on your 2009 Harley Ultra Classic:
- Locate the clock on your motorcycle. It is usually located on the instrument cluster.
- Turn the ignition key to the “On” position.
- Press and hold the “Mode” button until the clock starts flashing.
- Use the “Up” and “Down” buttons to adjust the hours.
- Press the “Mode” button again to move to the minutes.
- Use the “Up” and “Down” buttons to adjust the minutes.
- Press the “Mode” button one last time to save the changes.
Tips for Maintaining Clock Functionality
Here are some tips for maintaining the functionality of your clock:
Keep the battery in good condition.
A weak battery can cause the clock to lose time or stop working altogether. Make sure to replace the battery regularly, especially if you notice that the clock is starting to lose time.
Check the connections.
Loose or corroded connections can also cause the clock to malfunction. Make sure to check the connections regularly and clean them if necessary.
Avoid exposing the clock to extreme temperatures.
Extreme temperatures can damage the clock’s components. Try to keep the clock out of direct sunlight and extreme cold.
Don’t use harsh chemicals to clean the clock.
Harsh chemicals can damage the clock’s finish and components. Use a mild soap and water solution to clean the clock instead.
If the clock is still not working properly, take it to a qualified mechanic.
There may be a more serious problem that needs to be addressed. A qualified mechanic can diagnose the problem and repair the clock.
How to Set Clock on 2009 Harley Ultra Classic
1. Locate the clock on the instrument cluster. It is located in the center of the cluster, below the speedometer and tachometer.
2. Press and hold the “Mode” button on the left side of the instrument cluster.
3. Use the up and down arrow buttons on the right side of the instrument cluster to adjust the hour.
4. Press the “Mode” button to confirm the hour.
5. Repeat steps 3 and 4 to adjust the minutes.
6.Press the “Mode” button to confirm the time.
People Also Ask About How To Set Clock On 2009 Harley Ultra Classic
Where is the clock located on a 2009 Harley Ultra Classic?
The clock is located in the center of the instrument cluster, below the speedometer and tachometer.
How do I reset the clock on a 2009 Harley Ultra Classic?
To reset the clock, press and hold the “Mode” button for 5 seconds. The clock will reset to 12:00 AM.
How do I change the clock to military time on a 2009 Harley Ultra Classic?
The clock cannot be changed to military time on a 2009 Harley Ultra Classic.
