If the evaporator fan motor in your Electrolux LFHT2131QE1 refrigerator has failed, you’ll need to replace it to restore proper cooling. Replacing the evaporator fan motor is a relatively simple repair that can be completed in about an hour with a few basic tools. Replacing a broken evaporator fan motor in an Electrolux model LFHT2131QE1 is a straightforward task that can be completed with a few simple steps. Let’s get started.
First, you’ll need to unplug the refrigerator and remove the back panel. Locate the evaporator fan motor, which is usually mounted on the back of the refrigerator near the bottom. Once you’ve located the motor, disconnect the electrical connector and remove the mounting screws. Carefully remove the motor from the refrigerator. Then, take the new evaporator fan motor and insert it in place of the old one. Secure it with the mounting screws and reconnect the electrical connector. Finally, replace the back panel and plug the refrigerator back in. Your refrigerator should now be cooling properly again.
Replacing the evaporator fan motor in your Electrolux LFHT2131QE1 refrigerator is a simple repair that can be completed in about an hour. By following these steps, you can save the cost of calling a repairman and get your refrigerator back up and running quickly.
Locating the Evaporator Fan Motor
The evaporator fan motor is an essential component of your Electrolux LFHT2131QE1 refrigerator, as it circulates cold air throughout the appliance and helps maintain the optimal temperature for preserving food.
To access the evaporator fan motor, you need to locate the evaporator coil, which is usually situated behind the rear panel of the refrigerator’s freezer compartment. The evaporator fan motor is typically mounted on the side of the evaporator coil or inside the freezer compartment.
Here’s a detailed guide to locating the evaporator fan motor:
- Unplug the refrigerator and empty the freezer section: Before you begin working on the refrigerator, disconnect it from the power source and remove any food items from the freezer.
- Remove the rear panel of the freezer compartment: Use a screwdriver to remove the screws holding the rear panel in place. Carefully lift the panel off and set it aside.
- Locate the evaporator coil: The evaporator coil is a rectangular metal grid located at the back of the freezer compartment. It is typically covered with a thin layer of frost or ice.
- Identify the evaporator fan motor: The evaporator fan motor is usually mounted on the side of the evaporator coil or inside the freezer compartment. It is a small, black motor with a fan blade attached to it.
| Tool Required |
|---|
| Screwdriver |
Removing the Fan Motor Mount Screws
To access the evaporator fan motor in your Electrolux Lfht2131qe1 refrigerator, you need to remove the fan motor mount screws first. Here’s a step-by-step guide:
- Locate the fan motor mount screws. They are usually located on the back or side of the refrigerator, near the evaporator coils.
- Unplug the refrigerator. This is a safety precaution to prevent electric shock.
- Remove the back or side panel of the refrigerator. This will give you access to the fan motor mount screws.
- Identify the fan motor mount screws. They are usually small, Phillips-head screws.
- Use a screwdriver to remove the fan motor mount screws. Be careful not to strip the screws.
Here is a table of the sizes and locations of the screws that you may encounter:
| Screw Size | Location |
|---|---|
| #8 x 1/2″ | Back of refrigerator, near the evaporator coils |
| #10 x 3/4″ | Side of refrigerator, near the evaporator coils |
- Once the fan motor mount screws are removed, you can access the evaporator fan motor.
Inspecting the Fan Motor for Damage
Inspecting the fan motor is a crucial step in troubleshooting problems with your Electrolux refrigerator’s cooling system. Here’s a detailed guide on how to inspect the fan motor for damage:
1. **Unplug the refrigerator:** Before you begin, unplug the refrigerator from the power outlet for safety.
2. **Locate the fan motor:** The evaporator fan motor is typically located behind the back panel of the freezer compartment or behind the lower kickplate of the refrigerator.
3. **Remove the back panel or kickplate:** Carefully remove the screws or clips holding the back panel or kickplate in place.
4. **Disconnect the electrical connector:** Unplug the electrical connector leading to the fan motor.
5. **Remove the mounting screws:** Locate and remove the screws securing the fan motor to the housing.
6. **Visually inspect the motor:** Thoroughly examine the motor housing, blades, and electrical connections for any signs of damage, such as cracks, burn marks, or loose wires.
7. **Check for continuity:** Using a multimeter set to the ohms scale, test for continuity between the terminals on the fan motor. There should be a low resistance reading if the motor is functioning properly. If the reading is high or infinite, the motor may be faulty.
8. **Inspect the blades:** Examine the fan blades for any damage, such as bent or missing blades. Ensure that the blades rotate freely without obstruction.
9. **Reassemble the fan motor:** If no damage is found, reassemble the fan motor by following the steps in reverse order.
Reassembling the Refrigerator Components
Step 1: Connect the Evaporator Fan Motor Wires
Reconnect the gray wire to the terminal block screw on the left, and the blue wire to the screw on the right.
Step 2: Insert the New Evaporator Fan Motor Unit
Align the motor with the mounting holes in the evaporator fan housing and gently push it into place.
Step 3: Screw in the Evaporator Fan Motor
Secure the motor with the two screws and make sure they are tightened snugly.
Step 4: Reinstall the Evaporator Fan Housing
Position the housing back into the refrigerator and slide it into the slots until it snaps into place.
Step 5: Secure the Evaporator Fan Housing
Screw in the two screws at the top of the housing to keep it in place.
Step 6: Connect the Evaporator Fan Motor Harness
Plug the harness from the motor into the connector on the main control board and push it in securely.
Step 7: Reinstall the Shelves and Drawers
Replace the shelves and drawers that were removed for access.
Step 8: Reconnect the Refrigerator
Plug the refrigerator back into the power outlet and turn it on.
Step 9: Troubleshooting Verification
Verify Operation:
– Check if the evaporator fan motor is running smoothly and quietly.
– Monitor the refrigerator temperature to ensure it is cooling properly.
– Listen for any unusual noises or vibrations that may indicate a problem.
| Troubleshooting Tips |
|---|
| – If the motor is not running, check the electrical connections and ensure the power supply is adequate. |
| – If the refrigerator is not cooling, the evaporator coil may be frozen or there could be a refrigerant leak. |
| – If there are excessive noises or vibrations, the motor may be defective or improperly installed. |
How to Access Evaporator Fan Motor Electrolux LFHT2131QE1
Accessing the evaporator fan motor in an Electrolux refrigerator model LFHT2131QE1 can be achieved by following these steps:
- Unplug the refrigerator from the power outlet.
- Open the freezer door and locate the evaporator cover at the back of the freezer compartment. It is typically held in place by screws or clips.
- Remove the evaporator cover to expose the evaporator coils and the fan motor.
- Locate the evaporator fan motor, which is usually mounted on the side of the evaporator coils.
- Disconnect the electrical connector from the fan motor.
- Remove the mounting screws that hold the fan motor in place.
- Carefully lift the fan motor out of its housing.
To reassemble, simply reverse the steps above. Ensure that all electrical connections are secure and that the fan motor is properly mounted before plugging the refrigerator back into the power outlet.
