1. How To Change Trans Fluid On 2016 Honda Crv

How To Change Trans Fluid On 2016 Honda Crv

Changing the transmission fluid in your 2016 Honda CR-V is an important part of maintaining your vehicle. The transmission fluid helps to lubricate and cool the transmission, and it also helps to prevent wear and tear. Over time, the transmission fluid can become dirty and contaminated, which can lead to problems with the transmission. It is important to change the transmission fluid regularly to keep your transmission running smoothly.

Materials You Will Need

New transmission fluid
Drain pan
Funnel
Wrench
Rags

Step 1: Safety First

Before you start working on your car, it’s important to take some safety precautions. Park your car on a level surface and engage the parking brake. Allow the engine to cool down completely. Locate the transmission fluid drain plug and place the drain pan underneath it.

Step 2: Drain the Old Fluid

Use a wrench to loosen the drain plug and allow the old fluid to drain into the pan. Once the fluid has stopped draining, replace the drain plug and tighten it securely.

Step 3: Add New Fluid

Use a funnel to add new transmission fluid to the transmission. Add fluid until the level reaches the "Full" mark on the dipstick. Replace the dipstick and tighten the cap.

Step 4: Check the Fluid Level

Start the engine and let it run for a few minutes. Shift through all of the gears and then check the transmission fluid level again. Add more fluid if necessary to bring the level up to the "Full" mark.

Gathering Materials and Tools

Essential Materials and Tools

Before embarking on the task of changing the transmission fluid on your 2016 Honda CR-V, it is imperative to gather all the necessary materials and tools. Ensure you have the following items on hand:

Materials:

Honda Genuine CVT Transmission Fluid (approximately 6 liters)
New transmission filter
Transmission fluid pan gasket

Tools:

Tool	Description
10mm socket wrench	For removing transmission pan bolts
17mm socket wrench	For loosening fill plug and drain plug
Fluid drain pan	To catch the old transmission fluid
Funnel	For pouring in the new transmission fluid
Clean rags	For cleaning up any spills or debris
Torque wrench	For tightening bolts to specified torque values

Locating the Transmission

1. Safety First

Before you start, ensure the vehicle is parked on a flat and stable surface. Engage the parking brake to prevent any movement. Allow the engine to cool completely to avoid burns or accidents.

2. Identifying the Transmission

Locate the transmission pan underneath the vehicle. It is usually a rectangular-shaped metal pan located at the bottom of the transmission housing. To identify it accurately, consult your vehicle owner’s manual or refer to an online diagram specifically for your 2016 Honda CR-V model.

Once the transmission pan is identified, it’s essential to clean the surrounding area with a degreaser to remove any oil or debris that may interfere with the next steps. This will help prevent contamination during the fluid change.

Draining the Old Fluid

1. Make sure your Honda CR-V is parked on a level surface and the engine is cool.

2. Locate the drain plug on the transmission pan. It is usually a 17mm bolt located at the bottom of the pan.

3. Use a clean oil drain pan to catch the old fluid. Place the drain pan under the drain plug.

4. Use an appropriate tool (such as a socket wrench or box wrench) to loosen the drain plug. Be careful not to overtighten the plug, as this can damage the transmission pan.

5. Allow the old fluid to drain completely into the drain pan. This may take several minutes.

6. Once the old fluid has drained, clean the drain plug and reinstall it. Tighten the drain plug to the specified torque using a torque wrench.

7. Dispose of the old fluid properly at a local recycling center or automotive repair shop.

Step	Action
1	Park the vehicle on a level surface with the engine cool.
2	Locate the drain plug on the transmission pan.
3	Place a clean oil drain pan under the drain plug.
4	Use an appropriate tool to loosen the drain plug.
5	Allow the old fluid to drain completely.
6	Clean the drain plug and reinstall it.
7	Dispose of the old fluid properly.

Replacing the Transmission Pan Gasket

To replace the transmission pan gasket, you will need the following tools and materials:

10mm socket wrench
17mm socket wrench
New transmission pan gasket
Transmission fluid
Funnel
Rags

Steps:

1. Place the vehicle on a level surface and engage the parking brake.
2. Locate the transmission pan at the bottom of the transmission. There are two large bolts holding it in place.
3. Use the 17mm socket wrench to remove the two bolts.
4. Carefully lower the transmission pan and drain the transmission fluid into a drain pan.

Cleaning the Transmission Pan and Magnets

Once the transmission pan is removed, you will need to clean it and the magnets. Removing dirt and debris will help prevent contamination of the new fluid and help the pan seal properly. Use a clean rag to wipe the pan clean. Use a brush and solvent to remove the dirt and debris from the magnets. Inspect the magnet for any metal shavings or other foreign material. If you find any, it may indicate a transmission problem. consult a qualified mechanic for further diagnosis.

Parts Needed	Quantity
Transmission Pan Gasket	1
Transmission Fluid	3-4 quarts

5. Apply a thin bead of RTV sealant to the lip of the new transmission pan gasket.
6. Carefully place the new gasket on the transmission pan.
7. Lift the transmission pan and align it with the transmission.
8. Hand-tighten the two bolts.
9. Use the 17mm socket wrench to tighten the bolts to 18 ft-lbs.
10. Refill the transmission with the specified amount of fluid.
11. Start the engine and let it run for a few minutes.
12. Check for leaks.

Installing the New Transmission Filter

Replacing the transmission filter is a crucial step in ensuring the smooth and efficient operation of your 2016 Honda CR-V. Here’s how to do it:

Gather the necessary materials: New transmission filter, transmission fluid, drain pan, funnel, and socket wrench.

Locate the Transmission Filter

It is typically located on the side or bottom of the transmission housing. Refer to your vehicle’s service manual for the exact location.

Remove the Transmission Pan

Loosen the bolts holding the transmission pan in place and gently pry it off. Be careful not to spill any transmission fluid.

Extract the Old Transmission Filter

Using a pair of pliers or a screwdriver, remove the old transmission filter from the transmission housing. Inspect it for any debris or damage.

Inspect the Transmission Pan

While the transmission pan is off, inspect it for any metal shavings or other debris that may indicate internal transmission problems.

Install the New Transmission Filter

Lubricate the gasket of the new transmission filter with a small amount of clean transmission fluid. Align it with the housing and firmly press it into place until it makes a clicking sound. Tighten any bolts that secure the filter.

Reinstall the Transmission Pan

Clean the transmission pan and gasket before reinstalling it. Apply a thin layer of gasket maker to the gasket and place the pan back on the transmission housing. Tighten the bolts securely.

Add New Transmission Fluid: Refer to your vehicle’s service manual for the recommended amount of transmission fluid. Use the funnel to add the fluid through the dipstick tube.

Tightening the Transmission Pan Bolts

To finish the transmission fluid change, the transmission pan bolts need to be tightened. This step is crucial to ensure there are no leaks or loose fittings. Here are detailed instructions on how to tighten the transmission pan bolts on your 2016 Honda CR-V:

1. Locate the transmission pan bolts

The transmission pan bolts are located around the perimeter of the transmission pan. They are typically 10mm or 12mm bolts and may have washers underneath them.

2. Clean the bolt threads

Use a clean rag to wipe away any dirt or debris from the bolt threads. This will help prevent cross-threading and ensure a proper seal.

3. Apply thread sealant (optional)

For added protection against leaks, you can apply a small amount of thread sealant to the bolt threads. However, this is typically not necessary for modern vehicles.

4. Tighten the bolts

Use a torque wrench to tighten the bolts to the specified torque. Refer to the owner’s manual or repair manual for the exact torque specifications. Tightening the bolts too loosely can cause leaks, while overtightening can damage the pan or bolts.

5. Follow the tightening sequence

To ensure even tightening, follow a specific tightening sequence. Start by tightening the bolts located diagonally opposite each other. Then, gradually work your way around the pan, tightening the remaining bolts in a crisscross pattern.

6. Double-check tightness

Once all the bolts have been tightened, use the torque wrench to double-check the tightness. Ensure all bolts are torqued to the proper specifications. Additionally, you can check for any signs of leaks by inspecting the pan and surrounding area after driving the vehicle for a short distance.

Bolt Size	Torque Specification
10mm	9 ft-lb
12mm	13 ft-lb

Filling the Transmission with New Fluid

Once the old fluid has been drained, it’s time to fill the transmission with new fluid. Here’s a detailed guide on how to do it:

1. Locate the fill plug.

The fill plug is usually located on the side of the transmission case. It’s typically a 17mm or 19mm bolt.

2. Remove the fill plug.

Use a wrench to carefully remove the fill plug. Be careful not to drop it into the transmission.

3. Insert the funnel into the fill hole.

Place a funnel into the fill hole to make it easier to pour the new fluid.

4. Pour in the new fluid.

Start pouring the new fluid into the funnel. The amount of fluid needed will depend on the specific transmission. Consult your vehicle’s owner’s manual for the correct amount.

5. Check the fluid level.

Once you’ve poured in the new fluid, use a dipstick to check the fluid level. The dipstick should be inserted into the fill hole and pulled out to check the fluid level. The fluid should be between the “Full” and “Add” marks on the dipstick.

6. Repeat steps 4-5 until the fluid level is correct.

If the fluid level is low, add more fluid and check the level again. Repeat this process until the fluid level is correct.

7. Reinstall the fill plug.

Once the fluid level is correct, reinstall the fill plug. Tighten the plug securely, but do not overtighten it.

Tools Needed:
Wrench
Funnel
Dipstick

Checking the Fluid Level

Materials you’ll need:

– Clean rag or paper towels
– Funnel
– Trans fluid

Step-by-step instructions:
1. Park your CR-V on a level surface and allow the engine to cool.
2. Locate the transmission dipstick under the hood towards the back of the engine.
3. Remove the dipstick and wipe it clean with a rag or paper towels.
4. Reinsert the dipstick fully into the transmission and pull it out again.
5. Check the fluid level on the dipstick. It should be between the “COLD” and “HOT” marks.
6. If the fluid level is low, add fluid through the dipstick tube using a funnel.
7. Check the fluid level again and repeat steps 6-7 until the fluid level is correct.
8. **Detailed Steps for Step 8:**

Level	Cold	Hot
Overfilled	Above the HOT mark	Fluid can foam, overheat, and cause transmission damage.
Correct	Between the COLD and HOT marks	Optimal fluid level for proper transmission function.
Underfilled	Below the COLD mark	Insufficient lubrication can lead to premature transmission wear and failure.

Reinsert the dipstick fully into the transmission.
Start the engine and let it run for a few minutes.
Recheck the fluid level to ensure it is still correct.
If you have any concerns about the fluid level or condition, consult a qualified mechanic for further assistance.

Flushing the Old Fluid

• Warm up the engine and turn it off.

• Locate the transmission drain plug and position a drain pan underneath.

• Carefully remove the drain plug and allow the old fluid to drain into the pan.

Replacing the Filter

• Once the fluid has stopped draining, remove the transmission filter.

• Clean the filter housing and gasket surface.

• Lubricate the new filter gasket with fresh transmission fluid and install the new filter.

Refilling the Fluid

• Add 3.5 quarts of fresh transmission fluid to the gearbox.

• Start the engine and allow it to idle for a few minutes.

• Check the transmission fluid level using the dipstick and add more if necessary.

Resetting the Transmission Adaptation Values

• Connect a diagnostic scanner to the vehicle’s OBD-II port.

• Navigate to the “Transmission” menu.

• Select the “Reset Transmission Adaptation Values” option.

• Follow the on-screen prompts to complete the reset.

• This step can help ensure optimal transmission performance after the fluid change.

• Some models may not require this step, so it’s recommended to consult your vehicle’s service manual for specific instructions.

Completing the Fluid Change

1. Reinstall the drain bolt. Make sure to tighten it securely, but avoid overtightening.

2. Remove the fill bolt located near the top of the transmission case. Insert the funnel into the fill hole.

3. Pour the new fluid into the transmission, adding it slowly to avoid spills. Continue pouring until the fluid level reaches the bottom of the fill hole.

4. Reinstall the fill bolt and tighten it securely.

5. Clean up any spilled fluid and dispose of the old fluid and filter properly.

6. Reset the transmission control unit (TCU) adaptations. This can be done using a scan tool or by disconnecting the negative terminal of the battery for 30 minutes.

7. Start the engine and let it run for a few minutes, shifting through all the gears.

8. Check the transmission fluid level again and adjust as necessary.

9. Test drive the vehicle to ensure that the transmission is shifting smoothly and there are no leaks.

10. More Detailed Instructions for Step 10:

a. Drive the vehicle for about 10-15 miles, allowing the transmission to reach its operating temperature.

b. Park the vehicle on a level surface and engage the parking brake.

c. Remove the transmission fluid dipstick and wipe it clean with a rag.

d. Reinsert the dipstick all the way and then pull it out again. Check the fluid level on the dipstick. It should be within the “hot” range indicated on the dipstick.

e. If the fluid level is low, add more fluid through the fill hole using a funnel. If the fluid level is overfilled, remove some fluid using a turkey baster or syringe.

f. Reinsert the dipstick and recheck the fluid level to ensure it is correct.

How to Change Trans Fluid on a 2016 Honda CR-V

Changing the transmission fluid in your 2016 Honda CR-V is a relatively simple process that can be completed in about an hour. Here’s a step-by-step guide to help you get the job done:

Materials you’ll need:

New transmission fluid (Honda recommends using Honda Genuine ATF DW-1)
New transmission filter (Honda part number 25430-PLR-003)
New drain plug washer (Honda part number 94109-20000)
10mm socket wrench
17mm socket wrench
Funnel

Instructions:

Park the CR-V on a level surface and engage the parking brake.
Locate the transmission drain plug located on the bottom of the transmission pan. Place a drain pan under the drain plug.
Use a 17mm socket wrench to loosen the drain plug and allow the fluid to drain completely.
Once the fluid has drained, replace the drain plug and tighten it to 29 ft-lbs.
Locate the transmission filter located on the side of the transmission pan. Use a 10mm socket wrench to remove the bolts holding the filter in place.
Remove the old filter and replace it with the new one. Torque the bolts to 8 ft-lbs.
Clean the transmission pan and magnet of any metal shavings or debris.
Reinstall the transmission pan and torque the bolts to 8 ft-lbs.
Use a funnel to add new transmission fluid through the dipstick tube. Add 3.1 quarts of fluid.
Start the engine and allow it to idle for a few minutes.
Check the transmission fluid level using the dipstick. The fluid level should be between the “COLD” and “HOT” marks on the dipstick.
Add more fluid if necessary and recheck the level until it is correct.