Replacing a belt on a Maytag washer W10873035 is a relatively straightforward task that can be completed in about an hour. The most important thing is to make sure that you have the right belt for your model of washer. You can find the correct belt by looking up the model number of your washer in the Maytag parts catalog. Once you have the correct belt, you can follow the steps below to install it.
First, you will need to unplug the washer from the power outlet and turn off the water supply. Next, you will need to remove the back panel of the washer. To do this, locate the screws that are holding the back panel in place and remove them. Once the screws are removed, you should be able to pull the back panel off of the washer. Now, you will need to locate the belt. The belt is a long, black rubber band that is wrapped around the motor pulley and the transmission pulley. To remove the belt, simply slip it off of the pulleys. Finally, you will need to install the new belt. To do this, simply slip the new belt over the motor pulley and the transmission pulley. Once the new belt is in place, you can reattach the back panel of the washer. Make sure that the belt is tight before you reattach the back panel. To do this, simply turn the motor pulley by hand. The belt should be tight enough so that it does not slip off of the pulleys, but not so tight that it is difficult to turn the motor pulley.
Once the back panel is reattached, you can plug the washer back into the power outlet and turn on the water supply. Your washer should now be working properly.
Removing the Washer’s Front Panel
To initiate the dismantling process, meticulously unplug the washer’s power cord from the electrical outlet. This crucial safety measure prevents any potential electrical hazards. Locate the two screws securing the control panel to the top of the washer’s front panel. Using a Phillips head screwdriver, carefully remove these screws, being mindful not to damage the panel or surrounding components.
Proceed to the bottom of the front panel, where you will encounter two additional screws hidden behind the kickplate. These screws require a 1/4-inch hex head driver to extract. Once removed, gently pull the kickplate straight towards you to detach it from the washer.
With the kickplate out of the way, you can now focus on removing the front panel. Firmly grasp the panel on both sides and pull it towards you with steady force. The panel will be held in place by a series of plastic clips, which will release with a gentle tug. Once the clips are detached, slowly lift the panel upwards and out of the washer.
Caution: Handle the front panel with utmost care as it contains delicate electrical components. Avoid bending or twisting the panel to prevent damage.
| Tools Required |
|---|
| Phillips Head Screwdriver |
| 1/4-Inch Hex Head Driver |
Detaching the Drive Belt
The drive belt is a crucial component that powers the washer’s drum movement. To access and detach it, follow these steps:
Removing the Washer Top
1. Unplug the washer and disconnect the water hoses.
2. Locate the two screws at the back of the washer, near the top. Remove them using a screwdriver.
3. Carefully lift and remove the washer top, setting it aside.
Accessing the Drive Belt
4. Locate the drive belt pulley, which is usually attached to the motor at the bottom of the washer.
5. Using a pair of pliers or a spanner, gently pry the belt off the pulley.
6. Once the belt is detached, remove it from the washer.
Tips for Detaching the Belt
- Be cautious when prying the belt off the pulley, as it may be under tension.
- If the belt is stuck, use a small amount of penetrating oil to loosen it.
- Note the belt’s orientation for proper reinstallation.
| Component | Removal Process |
|---|---|
| Washer Top | Unplug, remove water hoses, unscrew and lift off |
| Drive Belt | Pry off pulley using pliers or spanner |
| Belt Tension | Use penetrating oil if stuck |
| Belt Orientation | Note position for reinstallation |
Installing the New Drive Belt
4. Installing the New Drive Belt
a) Place the new drive belt around the motor pulley, ensuring that it is seated correctly in the groove.
b) Route the belt around the idler pulley and tensioner pulley, following the correct routing diagram as per your washer model.
c) Position the belt around the transmission pulley, making sure to align it with the groove and guide pins.
d) Manually rotate the transmission pulley clockwise until the belt is tight. Check the tension by applying light pressure to the belt; it should deflect about 1/2 to 1 inch when pressed.
e) Tighten the tensioner pulley bolt or nut to secure the belt in place. Do not overtighten, as this can damage the belt or pulley.
f) Reconnect the electrical connectors to the transmission and motor.
g) Replace the back panel of the washer and secure it with screws.
Reattaching the Washer’s Front Panel
Once the new belt has been installed, it’s time to reattach the washer’s front panel. Here’s how:
1. Align the Panel
Carefully align the front panel with the washer’s frame, ensuring that the edges are flush and the panel is level.
2. Insert Top Tabs
Locate the two tabs at the top of the front panel and carefully insert them into the slots on the washer’s frame.
3. Push Down
Gently push down on the top of the front panel until you hear a click, indicating that the tabs have snapped into place.
4. Insert Bottom Clips
Locate the two clips at the bottom of the front panel and slide them into the slots on the washer’s frame.
5. Secure Screws
Use a screwdriver to tighten the screws that secure the front panel to the frame, ensuring that they are snug but not overtightened.
6. Install Kick Plate
The kick plate is a decorative panel that covers the bottom of the washer. To install it, follow these steps:
| Step | Instructions |
|---|---|
| a) | Position the kick plate at the bottom of the front panel. |
| b) | Insert the tabs on the kick plate into the slots on the front panel. |
| c) | Push down on the kick plate until it snaps into place. |
| d) | Use a screwdriver to tighten the screws that secure the kick plate to the front panel. |
Verifying Proper Belt Installation
After replacing the belt, it’s crucial to verify its proper installation. Follow these steps:
- Correct Belt Path: Ensure the belt follows the correct path around the motor pulley, idler pulley (if present), and transmission pulley.
- No Slack: The belt should be taut with no slack between the pulleys. A loose belt can slip and compromise performance.
- No Interference: Verify that the belt does not interfere or rub against any other components, such as wires, hoses, or the washer cabinet.
- Balanced Tension: The belt should have equal tension on both sides. Use a belt tension gauge or your fingers to check for any imbalances.
- Smooth Rotation: With the power off, manually rotate the motor pulley to check for any binding or excessive resistance. The pulleys should spin smoothly with a gentle push.
- Listening for Noises: Run a test cycle to listen for any abnormal noises coming from the belt area. A squealing or grinding sound may indicate misalignment or a damaged belt.
- Performance Check: If the belt appears to be installed correctly, run a full wash cycle to check for proper functionality. The washer should agitate, spin, and drain normally without any belt-related issues.
Materials You’ll Need
Before starting, gather the following materials:
– New drive belt (part number W10873035)
– Socket wrench or pliers
– Screwdriver
– Flashlight (optional)
Safety Precautions
Unplug the washer from the power outlet before beginning any repairs.
Wear gloves and safety glasses to protect yourself from sharp edges and debris.
Step-by-Step Instructions
1.
Remove the Top Panel
Locate the two screws holding the top panel in place. Remove the screws and lift the top panel off the washer.
2.
Locate the Drive Belt
The drive belt is located around the motor pulley and the transmission pulley at the bottom of the washer.
3.
Remove the Old Belt
Use a socket wrench or pliers to loosen the tension on the belt. Slip the belt off the pulleys and remove it from the washer.
4.
Install the New Belt
Place the new belt around the motor pulley first. Then, stretch the belt over the transmission pulley and adjust the tension using the socket wrench or pliers.
5.
Replace the Top Panel
Align the top panel with the washer and press it down until it clicks into place.
6.
Reconnect the Power
Plug the washer back into the power outlet.
7.
Test the Washer
Run the washer through a short cycle to ensure that the new belt is working properly.
Common Troubleshooting Tips
The belt keeps coming off
1. Check the tension on the belt. It should be tight enough to stay on the pulleys, but not so tight that it puts strain on the motor.
2. Ensure the belt is routed correctly around the pulleys.
3. Inspect the pulleys for damage. If they are worn or damaged, they may need to be replaced.
4. Check for other objects that may be caught in the belt, such as loose clothing or debris.
5. Replace the belt with a new one if it is damaged or stretched.
6. Check the motor bearings. If they are worn or damaged, they may cause the motor pulley to wobble, which can cause the belt to come off.
7. Inspect the transmission. If it is damaged or worn, it may not be able to turn the tub properly, which can cause the belt to come off.
8. Check the motor capacitor. If it is not working properly, it can cause the motor to run erratically, which can lead to the belt coming off. The motor capacitor is a cylindrical component that is connected to the motor. It is usually black or brown in color. To test the capacitor, you will need a multimeter. Disconnect the power to the washer before testing the capacitor. Set the multimeter to the capacitance setting and touch the probes to the terminals on the capacitor.
Safety Precautions for Washer Belt Installation
1. Unplug the washing machine or disconnect it from the power supply before starting any work.
2. Wear protective gloves and safety glasses to avoid injuries from sharp edges or chemicals.
3. Ensure the washing machine is stable and level before attempting to install the belt.
4. Clear the area around the washing machine of any obstacles or debris.
5. Have a helper assist you with lifting the appliance if necessary.
6. Make sure the washer is in its off cycle and the lid is open.
7. Remove the back or front panel of the washing machine, depending on the model.
8. Locate the old belt and carefully detach it from the pulleys.
9. Inspect the Belt for Damage
Inspect the old belt for any signs of damage, including cracks, cuts, fraying, or excessive wear. If any damage is found, replace the old belt with a new one to ensure optimal performance.
To thoroughly inspect the belt, use a magnifying glass to examine its surface for fine cracks or tears. Pay particular attention to the areas where the belt bends and makes contact with the pulleys.
Feel the belt’s texture to detect any rough spots, thinning, or areas where the rubber has hardened or become brittle. These indications could signal potential breakage or slippage during operation.
Additional Tips and Considerations
Unplug the washer before starting.
This is a crucial safety precaution to prevent any electrical shocks while working on the washer.
Gather the necessary tools.
You will need a screwdriver, a wrench, and a new belt.
Locate the belt.
The belt is usually located around the motor pulley and the transmission pulley.
Remove the old belt.
Use the wrench to loosen the tension on the belt and then slip it off the pulleys.
Install the new belt.
Slip the new belt onto the motor pulley first and then onto the transmission pulley. Make sure the belt is properly aligned and seated in the grooves.
Tighten the belt.
Use the wrench to tighten the tension on the belt. The belt should be tight enough to prevent slipping but not so tight that it puts unnecessary strain on the motor or the transmission.
Reassemble the washer.
Put the front panel back on and fasten the screws.
Test the washer.
Plug the washer back in and run it through a short cycle to make sure it is working properly.
10. Belt Tension Adjustment
Proper belt tension is crucial for optimal washer performance. If the belt is too loose, it may slip and cause the washer to vibrate or make noise. If the belt is too tight, it may put unnecessary strain on the motor and the transmission, leading to premature failure.
To adjust the belt tension, follow these steps:
| Step | Description |
|---|---|
| 1 | Loosen the two bolts that hold the motor mount in place. |
| 2 | Move the motor forward or backward to adjust the belt tension. |
| 3 | Tighten the bolts to secure the motor mount in place. |
| 4 | Run the washer through a short cycle to check the belt tension. |
Repeat these steps until the belt tension is correct.
How To Install Belt On Maytag Washer W10873035
Replacing the belt on a Maytag washer model W10873035 is a relatively simple repair that can be completed in about an hour. The most important thing is to make sure that you have the correct belt for your model and that you follow the instructions carefully.
Materials:
- New belt
- Screwdriver
- Bucket
Instructions:
- Unplug the washer from the power outlet.
- Turn off the water supply to the washer.
- Disconnect the drain hose from the standpipe.
- Tilt the washer back slightly and place a bucket under the bottom front of the washer to catch any water that may leak out.
- Remove the two screws that hold the front panel in place.
- Pull the front panel forward and off the washer.
- Locate the belt around the motor pulley and the transmission pulley.
- Loosen the idler pulley with a screwdriver.
- Remove the old belt from the pulleys.
- Place the new belt around the motor pulley and the transmission pulley.
- Tighten the idler pulley.
- Replace the front panel.
- Reconnect the drain hose to the standpipe.
- Turn on the water supply to the washer.
- Plug the washer into the power outlet.
- Run the washer through a test cycle.
People Also Ask About How To Install Belt On Maytag Washer W10873035
Can I replace the belt on my Maytag washer myself?
Yes, replacing the belt on a Maytag washer is a relatively simple repair that can be completed in about an hour. However, it is important to make sure that you have the correct belt for your model and that you follow the instructions carefully.
How do I know if the belt on my Maytag washer is broken?
There are several signs that may indicate that the belt on your Maytag washer is broken. These include:
- The washer will not agitate or spin.
- The washer makes a squealing or thumping noise.
- The washer leaks water.
How much does it cost to replace the belt on a Maytag washer?
The cost to replace the belt on a Maytag washer will vary depending on the model of the washer and the cost of the belt. However, you can expect to pay between $50 and $100 for the repair.
