Installing Tapco pivot springs is a simple and straightforward process that can be completed in just a few minutes. By following these step-by-step instructions, you can easily replace your old springs and restore your door to proper working order.
Before you begin, you will need to gather a few tools. These include a screwdriver, a pair of pliers, and a new set of Tapco pivot springs. Once you have all of your tools and materials, you can begin the installation process.
To start, locate the two screws that hold the pivot bar in place. Using a screwdriver, remove these screws and carefully lift the pivot bar out of the door frame. Next, take a pair of pliers and grip the old pivot springs. Gently twist the springs to remove them from the pivot bar. Finally, take the new pivot springs and insert them into the pivot bar. Make sure that the springs are facing the correct direction, as indicated by the arrows on the springs.
Adjust Spring Tension
The tension of the pivot springs can be adjusted to fine-tune the performance of the Tapco Enforcer. Adjusting the spring tension will affect the trigger pull weight and feel. To adjust the spring tension, follow these steps:
-
Remove the slide from the frame.
-
Identify the pivot spring screw on the bottom of the slide. It is typically located near the front of the slide, just above the trigger.
-
Using a small screwdriver, turn the pivot spring screw clockwise to increase the spring tension and counterclockwise to decrease the spring tension.
-
Adjust the spring tension in small increments and test the trigger pull to achieve the desired feel.
-
Continue adjusting the spring tension until you are satisfied with the trigger pull weight and feel.
-
Once you have adjusted the spring tension, reassemble the slide and frame.
Additional Notes:
The trigger pull weight will typically increase as the spring tension is increased. A heavier trigger pull weight can provide a more stable and controlled trigger pull, while a lighter trigger pull weight can make the gun easier to shoot quickly.
It is important to note that adjusting the spring tension can affect the reliability of the gun. If the spring tension is too weak, the gun may not cycle properly. If the spring tension is too strong, the trigger may be difficult to pull.
It is recommended to experiment with different spring tensions to find the optimal setting for your individual needs and preferences.
| Spring Tension | Trigger Pull Weight | Pros | Cons |
|---|---|---|---|
| Weak | Light | Easy to shoot quickly | May not cycle properly |
| Strong | Heavy | Stable and controlled trigger pull | Difficult to pull |
Clean Up
9. The last step is to clean up the springs and any debris that may have accumulated during the installation process. To do this, use a soft, damp cloth to gently wipe away any dirt or residue from the springs and the surrounding area. Be sure to avoid using any harsh chemicals or abrasive cleaners, as these could damage the springs or the finish on the door.
To ensure a smooth and long-lasting operation of the pivot springs, it is recommended to apply a small amount of lubricant to the springs and any moving parts. This will help to reduce friction and prevent any squeaking or noise.
Table: Recommended Lubricants for Pivot Springs
| Type of Lubricant | Benefits |
|---|---|
| White lithium grease | High temperature resistance, water-resistant |
| Teflon spray | Low friction, dry to the touch |
| Graphite powder | Non-staining, long-lasting |
How To Install Tapco Pivot Springs
Installing Tapco pivot springs is a relatively simple process that can be completed in a few minutes with the right tools. Here are the steps on how to do it:
- Remove the old pivot springs. To do this, simply use a pair of pliers to grip the spring and pull it out.
- Clean the pivot pin. Once the old springs are removed, use a clean cloth to wipe down the pivot pin to remove any dirt or debris.
- Install the new pivot springs. Take the new springs and place them on the pivot pin. Make sure that the springs are facing the correct direction.
- Tighten the pivot springs. Use a pair of pliers to tighten the springs until they are snug. Do not overtighten the springs, as this can damage them.
- Test the springs. Once the springs are installed, open and close the door a few times to make sure that they are working properly.
People Also Ask About How To Install Tapco Pivot Springs
Can I install Tapco pivot springs myself?
Yes, you can install Tapco pivot springs yourself. The process is relatively simple and only requires a few tools.
How do I know if my Tapco pivot springs need to be replaced?
There are a few signs that your Tapco pivot springs may need to be replaced. These include:
- The door is difficult to open or close.
- The door does not stay open when it is opened.
- The door squeaks or makes other noises when it is opened or closed.
Where can I buy Tapco pivot springs?
Tapco pivot springs can be purchased at most hardware stores.
