Navigating the intricacies of automotive maintenance can be daunting, but fret not. We embark on a journey to unravel the mysteries of removing a Nissan Rogue 09 mirror cover with ease and precision. Whether you’re an experienced mechanic or a novice venturing into the realm of DIY repairs, we’ve meticulously crafted this guide to lead you through the process seamlessly.
Before diving into the disassembly, it’s essential to gather the necessary tools: a flat-head screwdriver or plastic trim removal tool, a Phillips head screwdriver, and a pair of needle-nose pliers. With these tools at your disposal, you’re ready to embark on the task. Firstly, gently pry the small plastic cover near the mirror’s base using the flat-head screwdriver or trim removal tool. Behind this cover lies a single Phillips head screw, which you’ll carefully remove.
Once the screw is out, carefully lift the mirror cover upwards and towards the rear of the vehicle. You’ll encounter a series of clips securing the cover in place; gently pull on the cover while simultaneously applying pressure to release these clips. Once all the clips are disengaged, the mirror cover can be effortlessly removed, revealing the inner workings of the mirror assembly. Remember, meticulous attention to detail and a steady hand will ensure a hassle-free removal process.
Removing the Mirror Glass
To remove the mirror glass, you’ll need to:
-
Locate the release tabs. There are two release tabs located at the bottom of the mirror glass. To find them, gently grasp the edge of the glass and pull it towards you. As you pull, look for the tabs that will release the glass from the housing.
The release tabs are typically located on the bottom edge of the mirror glass. They are small, plastic tabs that can be pressed or squeezed to release the glass. To locate the tabs, insert a flat-head screwdriver or a plastic pry tool into the gap between the glass and the housing. Slowly pry the screwdriver or pry tool inward until you feel the tabs release.
Once you have found the release tabs, press or squeeze each tab to release the mirror glass from the housing. The glass should come loose and can be easily removed by hand.
-
Remove the glass. Once you have released the tabs, carefully lift the mirror glass up and away from the housing. Be careful not to drop the glass, as it is fragile.
-
Disconnect the electrical connectors. If your mirror has power mirrors, you will need to disconnect the electrical connectors before you can completely remove the glass. To do this, simply unplug the connectors from the back of the mirror glass.
-
Remove the old glass. Once the electrical connectors are disconnected, you can remove the old mirror glass from the housing. To do this, simply lift the glass up and out of the housing.
Removing the Mirror Cover
Step 1: Locate the Mirror Cover Retaining Clips
Find the small, black plastic clips located along the inner edge of the mirror cover. These clips attach the cover to the mirror housing.
Step 2: Insert a Trim Removal Tool or Flathead Screwdriver
Carefully insert a trim removal tool or a flathead screwdriver into the space between the mirror cover and the mirror housing. Work your way around the perimeter of the cover, prying it loose from the retaining clips. It may be helpful to apply gentle pressure to the outer edge of the cover while prying with the tool.
Tip: Use caution not to damage the mirror cover or the mirror housing during this process. If you encounter any resistance, stop and reevaluate your technique.
Step 3: Pull the Mirror Cover Free
Once all the retaining clips have been released, carefully pull the mirror cover straight towards you to remove it from the mirror housing. If the cover feels stuck, gently rock it back and forth while pulling until it comes loose.
Note: The mirror cover may have electrical connectors attached to it. If so, disconnect these connectors before completely removing the mirror cover.
Tools Required for Removal
To properly remove a Nissan Rogue 09 mirror cover, you will require a few basic tools. Here is a list of the necessary implements:
Pry Tool or Plastic Spudger
A pry tool or plastic spudger is essential for gently prying open the tabs or clips that hold the mirror cover in place. These tools are designed to avoid scratching or damaging the cover or surrounding components.
Screwdriver
In some cases, there may be screws that need to be removed before the mirror cover can be detached. For this purpose, you will need a screwdriver with the appropriate bit size and type (Phillips or flathead).
Towel or Soft Cloth
A towel or soft cloth can be used to protect the mirror cover and surrounding surfaces from scratches or damage during the removal process. It can be placed under the pry tool or spudger to prevent direct contact with the cover.
Gloves (Optional)
Wearing gloves can provide additional protection for your hands and prevent any fingerprints or smudges from getting on the mirror cover during handling.
| Tool | Purpose |
|---|---|
| Pry Tool or Plastic Spudger | Gently prying open tabs or clips |
| Screwdriver | Removing screws (if necessary) |
| Towel or Soft Cloth | Protecting surfaces from scratches |
| Gloves (Optional) | Hand protection and prevention of smudges |
Preparing the Mirror for Removal
Before you begin removing the Nissan Rogue’s mirror cover, it’s essential to prepare the mirror properly. This preliminary step will help prevent damage to the mirror assembly and ensure a smooth and efficient removal process.
1. Gather Necessary Tools
To remove the mirror cover, you will need a few basic tools, including a Phillips-head screwdriver, a flat-head screwdriver, or a pry tool. Ensure these tools are clean and in good condition before starting.
2. Clean the Mirror Surface
Thoroughly clean the mirror surface using a soft cloth or microfiber rag and a mild cleaner to remove any dirt or debris. This will prevent any abrasive particles from getting trapped during the removal process.
3. Protect the Glass
To prevent scratches or damage to the mirror glass, cover it with masking tape or a clean cloth before proceeding with the removal. This protective layer will shield the glass from any accidental bumps or scrapes.
4. Locate the Screws and Clips
Identify the screws or clips that hold the mirror cover in place. These are typically located around the perimeter of the cover, hidden beneath the plastic trim. Use a Phillips-head screwdriver to remove the screws, and a flat-head screwdriver or pry tool to carefully pry off the clips without damaging them.
| Screw/Clip Location | Tool Required |
|—|—|
| Top of the cover | Phillips-head screwdriver |
| Bottom of the cover | Phillips-head screwdriver |
| Outer edges of the cover | Flat-head screwdriver or pry tool |
Detaching the Mirror Glass
Detaching the mirror glass requires a bit more finesse. Follow these steps to ensure safe and accurate removal:
- Locate the clips: There will be two clips located on the back of the mirror glass, usually near the top and bottom corners.
- Use a pry tool: Insert a thin pry tool or a plastic trim removal tool into the gap between the mirror glass and the housing.
- Gently pry upward: Carefully pry the tool upwards, applying even pressure on both sides to avoid bending or cracking the glass.
- Release the glass: Once the clips are disengaged, carefully lift the mirror glass straight up to detach it from the housing.
- Disconnect the wiring harness: If the mirror has heated elements or other features, carefully unplug the wiring harness from the back of the mirror glass before completely removing it.
| Tip: |
|---|
| Use a soft cloth or a rubber pad when prying to protect the mirror surface from scratches. |
Removing the Cover Screws and Bolts
Step 1: Locate the Cover Screws
The mirror cover is held in place by a few screws located along the perimeter of the mirror. Identify these screws and prepare the necessary tools for removal.
Step 2: Remove the Cover Screws
Using a screwdriver or a socket wrench, carefully remove the screws that hold the cover in place. Ensure that you don’t overtighten the screws when reinstalling them later.
Step 3: Gently Pry Open the Cover
Once the screws are removed, gently pry open the mirror cover from the mirror base. Use a plastic trim removal tool or a flat-head screwdriver wrapped in a cloth to avoid scratching the paint or damaging the cover.
Step 4: Disconnect the Electrical Connectors
Behind the mirror cover, you may find electrical connectors that power the turn signal or the puddle lamp. Disconnect these connectors carefully by pressing on the release tabs and gently pulling them apart.
Step 5: Lift the Mirror Cover Off
With the screws removed and the electrical connectors disconnected, carefully lift the mirror cover off the mirror base. Be cautious not to damage any wires or components during this process.
Step 6: Removing the Bolts (Advanced)
In some Nissan Rogue models, the mirror cover may also be secured by bolts hidden behind the triangular pillar trim. To access these bolts:
- Unclip the triangular pillar trim and pull it gently away from the mirror.
- Locate the bolts concealed beneath the trim.
- Remove the bolts using a suitable wrench or socket.
- Once the bolts are removed, carefully pry open and lift off the mirror cover as described in Step 5.
| Screw/Bolt Location | Number of Screws/Bolts |
|---|---|
| Perimeter of Mirror | 4 |
| Behind Triangular Pillar Trim (Advanced) | 2 |
Lifting Off the Mirror Cover
Step 1: Gather Your Tools
You’ll need a small flathead screwdriver or pry tool.
Step 2: Locate the Release Clip
The release clip is located on the top corner of the mirror cover, towards the rear of the vehicle.
Step 3: Insert the Screwdriver or Pry Tool
Gently insert the tool into the slot of the release clip.
Step 4: Press and Lift Simultaneously
There are two small clips that hold the cover in place. Press down on the release clip with one hand while simultaneously lifting the cover with the other.
Step 5: Disconnect the Electrical Connector (If Applicable)
If your Nissan Rogue has power mirrors, there will be an electrical connector attached to the mirror cover. Press on the release tab and unplug the connector.
Step 6: Remove the Cover
Once the clips are released and the electrical connector is disconnected, you can fully remove the cover.
Step 7: Detailed Step-by-Step Guide
*
a. Position the Tool:
Align the screwdriver or pry tool with the release clip slot on the top corner of the mirror cover.
*
b. Angle and Force Application:
Position the tool at a slight angle and apply just enough downward pressure to engage the release clip.
*
c. Simultaneous Actions:
While maintaining pressure on the clip, gently lift the corresponding edge of the cover with your other hand.
*
d. Clip Release:
Continue pressing down while lifting until the two clips that hold the cover in place release.
*
e. Electrical Connector Detachment (if applicable):
For power mirrors, locate the release tab on the electrical connector and press it. Carefully unplug the connector before lifting the cover.
*
f. Cover Removal:
With the clips released and electrical connector disconnected, completely lift the cover to remove it from the mirror assembly.
Reattaching the Mirror Cover
Once the mirror cover is removed, it’s time to reattach it securely. Here’s a detailed step-by-step guide to help you do this:
- Align the Mirror Cover: Carefully align the mirror cover with the mounting points on the mirror housing.
- Apply Pressure: Apply firm pressure to the cover, starting from one end and working your way to the other.
- Secure with Clips: If the mirror cover has any clips or fasteners, push them into place to secure it.
- Check Alignment: Ensure that the mirror cover is properly aligned and flush with the mirror housing.
- Clean and Inspect: Use a clean damp cloth to wipe down the mirror cover and surrounding area.
- Check Functionality: Adjust the mirror to ensure that it functions properly.
- Additional Tips: If the cover is loose or rattling, try tightening the clips or fasteners further.
- Professional Assistance: If you encounter any difficulties or concerns, don’t hesitate to consult with a qualified mechanic or dealership for professional assistance.
Remember to follow these steps carefully to ensure a secure and functional mirror cover. If you have any further questions, refer to the vehicle’s owner’s manual or seek guidance from a reliable source.
Sourcing the Right Tools
Having the appropriate tools on hand is crucial for a hassle-free removal process. Gather: A Phillips screwdriver, a flat-head screwdriver, and a plastic pry tool (optional). Using the correct tools helps prevent damage to your vehicle’s components.
Locating the Release Tab
Begin by locating the release tab beneath the mirror cover. It’s typically situated near the base of the cover, close to the vehicle’s frame. Gently press the tab with your flat-head screwdriver to release the cover.
Gently Prying the Cover Loose
Once you’ve located and pressed the release tab, insert the plastic pry tool (or flat-head screwdriver) into the gap created. Carefully pry the cover loose, working your way around the perimeter. Avoid using excessive force, as this may damage the cover or the mirror.
Unclipping the Electrical Connectors
After you’ve successfully pried the mirror cover loose, you’ll need to unclip the electrical connectors that power the mirror’s functions. Pinch the sides of the connectors and gently pull them apart.
Detaching the Turn Signal
If your Nissan Rogue has a turn signal integrated into the mirror cover, you’ll need to detach it. Locate the small screws holding the turn signal in place and remove them using the Phillips screwdriver. Disconnect the electrical connector attached to the turn signal and set it aside.
Removing the Mounting Bolts
Once the mirror cover is completely free, locate the mounting bolts that secure it to the mirror base. Remove these bolts using the Phillips screwdriver or wrench.
Lifting Off the Mirror Cover
With the mounting bolts removed, you’re ready to lift off the mirror cover. Carefully lift it upwards and away from the mirror base, being mindful of any remaining electrical wires or connectors.
Replacing the Mirror Cover
If you’re replacing the mirror cover, follow the above steps in reverse order to install the new one. Ensure that all bolts and connectors are securely fastened.
Additional Tips for a Smooth Removal
Before starting the process, park your vehicle on a flat, stable surface.
Protect your vehicle’s paint by covering it with a clean cloth or towel.
If you encounter resistance when prying the cover loose, apply gentle, even pressure. Avoid using excessive force or prying tools made of metal, as they may damage the cover.
When reattaching the electrical connectors, make sure they’re fully engaged to prevent malfunctioning of the mirror’s functions.
Troubleshooting Common Issues
Problem: Mirror cover is loose or rattling
Tighten the screws that secure the mirror cover to the mirror base. Replace any damaged or missing screws.
Problem: Mirror cover is discolored or faded
Clean the mirror cover with a mild soap solution. Apply a UV protectant to prevent further damage.
Problem: Mirror cover is cracked or damaged
Replace the damaged mirror cover. This may require removing the entire mirror assembly.
Problem: Mirror cover is misaligned
Adjust the alignment of the mirror cover by loosening the screws and moving it into the correct position. Tighten the screws securely.
Problem: Mirror cover is not heating up
Check the electrical connections to the mirror cover. Replace any faulty connectors or wires.
Problemm: Mirror cover is not folding or extending
Check the fuse for the mirror system. Replace the fuse if it is blown. Lubricate the mirror folding mechanism.
Problem: Mirror cover is obstructing the view
Adjust the mirror cover to a lower position or fold it in if possible.
Problem: Mirror cover is making a noise
Check for any loose screws or fasteners that may be causing the noise. Tighten or replace any loose components.
Problem: Mirror cover is not latching properly
Clean the latch mechanism and lubricate it with a light lubricant. Replace the latch if it is damaged.
Problem: Mirror cover has a broken adjustment knob
Replace the adjustment knob. This may require removing the entire mirror assembly.
How To Remove A Nissan Rogue 09 Mirror Cover
Before starting the process of removing the mirror cover on a Nissan Rogue 09, it is important to have the necessary tools and materials. These include a flathead screwdriver, a Phillips head screwdriver, and a new mirror cover (if replacing). Follow the steps below to safely remove the original mirror cover:
- Locate the Screws:
Start by identifying the three screws that secure the mirror cover to the mirror assembly. There is usually one screw located at the top of the cover, one in the middle, and one at the bottom. - Remove the Screws:
Insert the Phillips head screwdriver into the screw head and carefully unscrew all three screws. Avoid overtightening or stripping the screws. - Pry Open the Cover:
Use the flathead screwdriver to gently pry open the top edge of the mirror cover. Be cautious not to damage the cover or the mirror assembly. - Unclip the Cover:
Once the top edge is open, carefully move the flathead screwdriver along the sides and bottom of the cover to release the clips that hold it in place. There are typically several clips around the perimeter. - Slide Off the Cover:
Gently pull the mirror cover towards you to slide it off the mirror assembly. Avoid using excessive force to prevent breakage.
People Also Ask
How do I remove a Nissan Rogue mirror cap?
- The process of removing a Nissan Rogue mirror cap is similar to removing the mirror cover. Locate the screws and unscrew them, pry open the top edge of the cap, unclip the cap, and slide it off the mirror assembly.
How do I replace a mirror cover on a Nissan Rogue?
- Once the original mirror cover is removed, align the new cover with the mirror assembly. Push firmly around the edges until the clips engage and the cover is securely in place. Tighten the screws to secure the cover.
