Are you seeking to remove your Ring Doorbell Pro to replace it with a new one, relocate it to a different spot, or for any other reason? Removing a Ring Doorbell Pro is a relatively simple process that can be completed in a few steps. Whether you’re an experienced DIY enthusiast or a first-timer, this guide will provide you with clear instructions and helpful tips to ensure a successful removal. Once you have removed your Ring Doorbell Pro, you can proceed with the necessary actions, such as installing a new doorbell or storing it for future use.
Before you begin the removal process, it is crucial to gather the necessary tools. You will need a Philips head screwdriver, a small flathead screwdriver, and a pair of needle-nose pliers. Additionally, if your Ring Doorbell Pro is currently powered by batteries, you will need to remove them. Once you have all the necessary tools and materials, you can proceed with the following steps: 1. Remove the faceplate by inserting the small flathead screwdriver into the notch at the bottom of the faceplate and gently prying it off. 2. Use the Philips head screwdriver to remove the two screws that secure the mounting bracket to the wall.
3. Carefully pull the Ring Doorbell Pro straight towards you, disconnecting it from the mounting bracket. 4. If your Ring Doorbell Pro is wired, disconnect the wires from the terminals on the back of the device. 5. Remove the mounting bracket from the wall by unscrewing the two screws that secure it. Once you have completed these steps, your Ring Doorbell Pro will be successfully removed from the wall. You can now proceed with the next steps, such as installing a new doorbell or storing the Ring Doorbell Pro for future use. Remember to handle the device with care throughout the removal process to avoid any damage.
Safely Disconnect the Power
Before you begin:
It’s crucial to take proper precautions before disconnecting the power to your Ring Doorbell Pro. Follow these safety tips to avoid any potential hazards:
- Identify the main power source: Determine whether your Doorbell Pro is powered by batteries or a wired connection. If it’s wired, you’ll need to locate the circuit breaker or fuse box that supplies power to the doorbell.
- Turn off power at the main breaker: Once you’ve identified the power source, turn off the power to the circuit that feeds your doorbell. This will ensure there’s no electrical current flowing through the device when you disconnect it.
- Double-check for power: Use a multimeter or voltage tester to confirm that the power to the doorbell has been successfully disconnected. This will give you peace of mind and prevent any electrical accidents.
Additional Precautions:
| Scenario | Precautions |
|---|---|
| Battery-powered Doorbell Pro | Remove the batteries from the device before disconnecting it. |
| Wired Doorbell Pro | Turn off the power at the circuit breaker or fuse box and disconnect the doorbell’s wires from the electrical junction box. |
| Shared Power Source | If your Doorbell Pro shares a power source with other devices, disconnect all connected devices before turning off the power. |
Remember, safety should always be your top priority when working with electrical devices. By following these precautions, you can ensure a safe and successful removal of your Ring Doorbell Pro.
Remove the Faceplate
To remove the faceplate from your Ring Doorbell Pro, follow these steps:
- Remove the screw. Use a Phillips screwdriver to remove the single screw located in the bottom center of the faceplate.
- Pry the faceplate off. Carefully pry the faceplate off the doorbell base using a plastic pry tool or a flat-head screwdriver. Avoid using excessive force, as you may damage the device or surrounding surfaces.
- Disconnect the doorbell wire (optional). If you’re planning to move your doorbell to a new location, you’ll need to disconnect the doorbell wire. To do this, simply push down on the wire connector tab and pull the wire out.
Additional Tips for Removing the Faceplate Safely
Here are some additional tips for removing the faceplate of your Ring Doorbell Pro safely and efficiently:
- Ensure that you have the correct tools for the job, such as a Phillips screwdriver and a plastic pry tool or flat-head screwdriver.
- Apply gentle pressure when prying the faceplate off to avoid damaging the device or surrounding surfaces.
- If you encounter any resistance when removing the faceplate, stop and inspect the area for any obstacles or obstructions.
- If you’re disconnecting the doorbell wire, make sure to push down on the wire connector tab firmly to release the wire.
| Step | Action |
|---|---|
| 1 | Locate and remove the screw using a Phillips screwdriver. |
| 2 | Use a plastic pry tool or flat-head screwdriver to carefully pry off the faceplate. |
| 3 (optional) | If moving the doorbell, disconnect the doorbell wire by pressing down on the wire connector tab and pulling out the wire. |
Detach the Mounting Bracket
The first step in removing your Ring Doorbell Pro is to detach the mounting bracket. To do this, you will need to remove the two screws that are located on the bottom of the bracket. Once the screws are removed, you can gently pull the bracket away from the wall.
If you find that the bracket is stuck, you can use a screwdriver or a pair of pliers to gently pry it loose. Be careful not to damage the bracket or the wall when doing this.
Once the bracket is detached, you will need to disconnect the wires that are connected to the doorbell. To do this, simply use your fingers to pinch the terminals on the back of the doorbell and pull the wires out.
Here is a table that summarizes the steps involved in detaching the mounting bracket:
| Step | Action |
|—|—|
| 1 | Remove the two screws that are located on the bottom of the bracket. |
| 2 | Gently pull the bracket away from the wall. |
| 3 | If the bracket is stuck, use a screwdriver or a pair of pliers to gently pry it loose. |
| 4 | Disconnect the wires that are connected to the doorbell. |
Disassemble the Power Kit
The Power Kit is the part of the Ring Doorbell Pro that connects the doorbell to your home’s electrical system. To remove the Ring Doorbell Pro, you need to first disassemble the Power Kit that connects the doorbell to the wiring of your home. Here’s how to do it:
- Turn off the power to your doorbell at the circuit breaker or fuse box.
- Remove the two screws that hold the faceplate of the Power Kit in place.
- Pull the faceplate straight out from the wall.
- Inside the Power Kit, you will see four wires:
- Once the wires are disconnected, you can remove the Power Kit from the wall.
| Wire | Description |
|---|---|
| White | Neutral wire |
| Black | Hot wire |
| Green | Ground wire |
| Red | Power wire |
Disconnect the wires from the Power Kit by loosening the screws on the wire terminals. Make sure to remember which wire was connected to which terminal.
Uninstall the Electrical Wires
Step 1: Turn off the power to your Ring Doorbell Pro at the circuit breaker or fuse box. This is a crucial safety measure to prevent electrical shocks.
Step 2: Remove the faceplate of your Ring Doorbell Pro by unscrewing the two security screws located at the bottom of the device.
Step 3: Disconnect the wires from the Ring Doorbell Pro terminals. Note the positions of the wires (usually labeled “FRONT” and “REAR”) so you can reconnect them correctly later.
Step 4: Use a screwdriver or wire strippers to loosen the terminal screws and carefully remove the wires.
Step 5: Pull the wires gently out of the wall to create some slack. You may need to use a pair of needle-nose pliers to grip the wires securely.
| Rear | Front |
|---|---|
| White wire (-) | Black wire (+) |
Step 6: Tape the ends of the wires together using electrical tape to prevent them from touching and creating a short circuit.
Step 7: Tuck the wires back into the wall and secure them with electrical tape or wire nuts.
Step 8: Restore power to your Ring Doorbell Pro by turning the circuit breaker or fuse back on.
Remove the Chime Kit (If Installed)
If you’ve installed a Ring Doorbell Pro with a chime kit, you’ll need to remove it before proceeding. Here’s how:
Step 1: Locate the chime kit.
It’s typically mounted on a wall near an existing doorbell chime.
Step 2: Turn off power to the chime kit.
Flip the breaker that controls the chime kit’s circuit or remove the fuse.
Step 3: Disconnect the chime kit from the wall.
Use a screwdriver to remove the screws holding it in place.
Step 4: Disconnect the wires from the chime kit.
Take a picture of the wiring configuration before disconnecting any wires. This will help you rewire the chime kit later if needed.
Step 5: Remove the chime kit from the wall.
Once the wires are disconnected, you can pull the chime kit away from the wall and remove it completely.
Step 6: Cap the exposed wires.
Using electrical tape or wire nuts, cap the exposed wires on the wall and on the chime kit. This will prevent electrical shocks and short circuits.
| Wire Color | Connection |
|---|---|
| Red | Transformer terminal (positive) |
| Black | Transformer terminal (negative) |
| White | Front doorbell button |
| Yellow | Rear doorbell button (if applicable) |
Reset the Ring Doorbell Pro
Step 1: Remove the Faceplate
Gently pry off the faceplate covering the doorbell’s buttons and camera.
Step 2: Locate the Reset Button
Inside the doorbell, find the small, black reset button located near the bottom.
Step 3: Insert a Pin
Use a small pin or paperclip to gently press and hold the reset button for 15 seconds.
Step 4: Release the Button
After 15 seconds, release the reset button.
Step 5: Wait for the Blue Ring
The doorbell will flash a blue ring around the button to indicate it is resetting.
Step 6: Reinstall the Faceplate
Once the blue ring has stopped flashing, replace the faceplate over the doorbell.
Step 7: Reconfigure the Doorbell
a) Open the Ring App
Launch the Ring app on your smartphone and log in to your account.
b) Select the Doorbell
Choose the Ring Doorbell Pro you want to reconfigure from the list of devices.
c) Follow the Prompts
Follow the on-screen instructions in the app to reconnect your doorbell to Wi-Fi and complete the setup process.
Verify Successful Removal
Once you have completed the steps above, it’s important to verify that the Ring Doorbell Pro has been successfully removed. Here’s how:
Checking the Ring App
Open the Ring app on your mobile device. If the Ring Doorbell Pro has been removed successfully, it will no longer appear in the list of devices.
Checking Your Gateway
If you have a Ring Chime Pro or Ring Chime, it will show a blue light when the Ring Doorbell Pro is connected. If the Ring Doorbell Pro has been removed successfully, the blue light on the Gateway will turn off.
Checking for Physical Disconnection
Go to where the Ring Doorbell Pro was installed. If it has been removed successfully, the doorbell will no longer be physically connected to the wiring.
Troubleshooting
If you’ve followed the steps above but the Ring Doorbell Pro is still appearing in the Ring app or the Gateway is still showing a blue light, try the following:
- Make sure that you have completed all the steps in the removal process.
- Restart the Ring Doorbell Pro by pressing the orange button on the back of the device.
- Restart the Ring app on your mobile device.
- Contact Ring support for further assistance.
Clean the Mounting Area
Before removing your Ring Doorbell Pro, it’s important to clean the mounting area to prevent any residue or dirt from affecting the installation process. Here’s how to clean it effectively:
1. Gather the Necessary Tools
You’ll need a soft cloth, rubbing alcohol, and a screwdriver or drill.
2. Turn Off the Power
Switch off the breaker or fuse that powers the doorbell to ensure safety.
3. Remove the Faceplate
Use a screwdriver to unscrew the two screws at the bottom of the faceplate and lift it off the base.
4. Clean the Base
Wipe down the base of the doorbell with a soft cloth dampened with rubbing alcohol. Make sure to remove any dirt or debris.
5. Clean the Mounting Surface
Using a damp cloth, wipe down the area where the doorbell was mounted to remove any dirt or residue. Ensure it’s completely dry before continuing.
6. Remove the Mounting Plate
Unscrew the four screws that secure the mounting plate to the mounting surface. Carefully lift the plate off.
7. Clean the Screws
Wipe down the screws with rubbing alcohol to remove any dirt or debris.
8. Inspect the Seal
Check the rubber seal around the mounting plate. If it’s damaged or worn, replace it before installing the new doorbell.
9. Clean the Wires
If you’re replacing the doorbell with a wired model, clean the wires using rubbing alcohol. Ensure they’re free of dirt or corrosion. You can also use a wire brush to remove any stubborn residue or oxidation.
| Materials | Usage |
|---|---|
| Soft cloth | Wiping surfaces |
| Rubbing alcohol | Cleaning surfaces and wires |
| Screwdriver or drill | Removing screws |
Secure the Hole or Wires
Once the doorbell is disconnected, you need to secure the hole where it was mounted. If you don’t, water, insects, or other debris can enter your home through the opening. There are a few ways to do this, depending on the type of surface the doorbell was mounted on.
If the doorbell was mounted on brick or concrete:
- Fill the hole with a silicone or polyurethane caulk using a caulk gun.
- Smooth the caulk with your finger or a putty knife.
- Allow the caulk to dry completely, which may take several hours or days, depending on the type of caulk used.
If the doorbell was mounted on wood:
- Cut a small piece of wood to fit over the hole.
- Glue or nail the wood piece into place.
- Paint or stain the wood piece to match the surrounding area.
If the doorbell was mounted on vinyl siding:
- Remove the siding panel that the doorbell was mounted on.
- Cut a piece of scrap siding to fit over the hole.
- Glue or nail the scrap siding into place.
- Reinstall the siding panel.
If the doorbell was mounted on a surface other than brick, concrete, wood, or vinyl siding:
- Consult with a home improvement professional for advice on the best way to secure the hole.
In addition to securing the hole, you also need to take care of the wires that were connected to the doorbell. If the wires are not properly insulated, they could become a fire hazard. Cut the wires close to the doorbell and then wrap them with electrical tape or cover them with wire nuts.
How to Remove a Ring Doorbell Pro
To remove a Ring Doorbell Pro, follow these steps:
1.
Turn off the power to your doorbell by flipping the breaker or removing the fuse.
2.
Remove the faceplate by unscrewing the two screws at the bottom.
3.
Disconnect the wires from the terminals on the back of the doorbell.
4.
Remove the two screws that are holding the doorbell in place.
5.
Pull the doorbell straight out of the wall.
People Also Ask About Removing a Ring Doorbell Pro
How to remove a Ring Doorbell Pro that is hardwired?
If your Ring Doorbell Pro is hardwired, you will need to disconnect the wires from the terminals on the back of the doorbell before you can remove it. To do this, use a small screwdriver to loosen the screws on the terminals and then pull the wires off.
How to remove a Ring Doorbell Pro that is battery-powered?
If your Ring Doorbell Pro is battery-powered, you will need to remove the battery before you can remove the doorbell. To do this, use a small screwdriver to loosen the screw on the bottom of the doorbell and then pull the battery out.
