Unclog a kitchen sink that frustrates you, and the pile of dirty dishes waiting to be washed becomes a mountain. But if you know how to remove an EZ Mount sink flange kit, you can access the P-trap and clean out the clog in no time. This easy fix will save you time, money, and a lot of frustration.
Before you begin, gather a few tools: a flathead screwdriver, a pair of pliers, and a bucket. You may also want to wear gloves to protect your hands from the dirty water. Once you have your tools, you can start by removing the decorative cover from the sink flange. This cover is usually held in place by a few screws. Once the cover is removed, you will see the sink flange, which is attached to the sink by a series of clips. Use the pliers to squeeze the clips and detach the flange from the sink.
Finally, you can remove the P-trap by unscrewing the nuts that hold it in place. Be careful not to spill any water when you remove the P-trap. Once the P-trap is removed, you can clean out the clog. Once the clog is cleared, you can reassemble the P-trap and the sink flange. Start by attaching the P-trap to the sink drain. Then, attach the sink flange to the sink. Finally, replace the decorative cover. Your sink is now unclogged and ready to use!
Prepare the Work Area
Before beginning the process of removing the EZ Mount Sink Flange Kit, it is crucial to adequately prepare the work area. This preparation ensures a safe and efficient procedure.
1. Clear the Cabinet and Sink Area:
• Empty the cabinet below the sink and remove any items stored inside.
• Clear the surrounding countertop of any appliances, dishes, or other obstacles.
• Place a drop cloth or thick towels on the floor beneath the sink to protect it from water or debris.
• Ensure there is ample working space around the sink to move freely.
2. Shut Off Water Supply:
• Locate and close the water supply valves under the sink or near the water meter.
• Turn on the faucets to release any remaining water in the pipes.
3. Disconnect Plumbing:
• Use a wrench or pliers to loosen and remove the water supply lines connected to the faucet.
• Detach the drainpipe from the sink drain using a basin wrench or slip-joint pliers.
• Carefully lift the sink to disconnect it from the drainpipe and plumbing connections.
Disconnect the Plumbing
Step 1: Turn off the Water Supply
Locate the water supply valves under the sink and turn them off. These valves are typically located on the hot and cold water lines.
Step 2: Disconnect the Water Lines
Once the water supply is turned off, use an adjustable wrench to disconnect the water lines from the sink flange. Place a bucket or towel under the connections to catch any remaining water.
Step 3: Disconnect the Drain Line
If the sink has a garbage disposal, disconnect the drain line from the disposal. If not, locate the slip nut that connects the drain line to the sink flange and loosen it with pliers. Pull the drain line off the flange.
Step 4: Remove the Sink Strainer
Remove the sink strainer by unscrewing it counterclockwise. This will expose the mounting nuts that hold the sink flange in place.
Table: Ez Mount Sink Flange Kit Components
| Component | Description |
|---|---|
| Flange | A metal or plastic ring that fits over the drain hole in the sink |
| Mounting Nuts | Nuts that hold the flange in place |
| Washers | Washers that provide a seal between the flange and the sink |
| Basket Strainer | A strainer that fits inside the flange and prevents debris from entering the drain |
| Overflow Plate | A plate that fits over the overflow hole in the sink and prevents water from overflowing |
Remove the Sink
1. Turn off the water supply to the sink.
2. Disconnect the water supply lines from the sink.
3. Loosen the nuts that hold the sink in place. To do this, you will need a wrench or pliers. Once the nuts are loose, you can lift the sink out of the hole in the countertop.
Tools You’ll Need
| Tool | Description |
|---|---|
| Wrench or pliers | To loosen the nuts that hold the sink in place |
| Flashlight | To see inside the cabinet under the sink |
| Bucket | To catch any water that may leak out when you disconnect the water supply lines |
Remove the Old Flange Kit
To remove the old flange kit, you will need a few tools:
- Adjustable wrench
- Putty knife
- Utility knife
- Bucket
Once you have these tools, you can follow these steps to remove the old flange kit:
1. Turn off the water supply to the sink.
2. Disconnect the drain line from the flange.
3. Loosen the nuts that hold the flange in place.
4. Carefully remove the flange from the sink.
Step 4: Carefully remove the flange from the sink
This step can be tricky, so be careful not to damage the sink. Here are a few tips:
- Use a putty knife to loosen the old caulk around the flange.
- Use a utility knife to cut through the old caulk.
- Gently pry the flange away from the sink.
- If the flange is stuck, use an adjustable wrench to loosen the nuts.
- Once the flange is loose, remove it from the sink.
Clean the Sink Opening
Before removing the Ez Mount Sink Flange Kit, it is crucial to clean the sink opening thoroughly to ensure a proper seal and prevent any leaks. Here are the steps involved in cleaning the sink opening:
- Remove any debris: Use a sponge or brush to remove any visible debris or food particles from the sink opening.
| Materials Needed |
|---|
|
- Apply dish soap: Apply a generous amount of dish soap to the sink opening and use the sponge or brush to scrub the surface. This will help remove any dirt or grease.
- Rinse thoroughly: Rinse the sink opening thoroughly with water to remove all traces of dish soap.
- Dry the surface: Use a clean cloth to dry the surface of the sink opening. Make sure it is completely dry before proceeding with the removal of the Ez Mount Sink Flange Kit.
By cleaning the sink opening thoroughly, you will ensure a strong and leak-proof seal when installing the new Ez Mount Sink Flange Kit.
Apply a Bead of Sealant
After cleaning and drying the sink flange, apply a continuous bead of kitchen and bath silicone sealant around the perimeter of the flange. The bead should be about 1/4 inch thick and should be applied evenly. It is important to make sure that the sealant is applied to all surfaces that will be in contact with the sink and the countertop, including the underside of the sink flange.
Once the sealant has been applied, allow it to set for the amount of time specified by the manufacturer’s instructions. This will typically be around 24 hours, but it is important to check the specific instructions for the sealant that you are using.
Tips for Applying a Bead of Sealant
Here are a few tips for applying a bead of sealant:
| Step | Tip |
|---|---|
| 1 | Use a caulking gun to apply the sealant. This will help you to get a smooth, even bead. |
| 2 | Hold the caulking gun at a 45-degree angle to the surface that you are sealing. |
| 3 | Apply the sealant in a continuous bead, without stopping or starting. |
| 4 | Smooth the bead of sealant with your finger or a damp sponge. |
| 5 | Allow the sealant to set for the amount of time specified by the manufacturer’s instructions. |
Install the New Flange Kit
Once the old flange kit has been removed, it’s time to install the new one. Here’s a step-by-step guide:
- Clean the sinkhole before installing the new flange.
- Apply a bead of plumber’s putty around the inside rim of the new flange.
- Insert the new flange into the sinkhole and tighten the screws.
- Wipe away any excess putty.
- Attach the sink to the flange and tighten the nuts.
- Reconnect the P-trap and water supply lines.
- Finish the Installation
- Caulk the Joint: Apply a bead of silicone caulk around the joint between the sink and the flange. Smooth the caulk with your finger or a caulk tool.
- Wipe Away Excess Caulk: Use a damp cloth to wipe away any excess caulk. Be careful not to smear the caulk.
- Inspect the Installation: Turn on the water supply and check for leaks. If there are no leaks, the installation is complete.
Secure the Sink
1. Place a block of wood or a piece of cardboard under the sink to support it while you work.
2. If the sink is already installed, disconnect the water supply lines and the drainpipe.
3. Remove the mounting screws or bolts that secure the sink to the countertop.
4. Carefully lift the sink out of the countertop.
Remove the Ez Mount Sink Flange Kit
5. Locate the Ez Mount sink flange kit under the sink.
6. Using a screwdriver, loosen the screws that secure the flange to the countertop.
7. Carefully remove the flange from the countertop.
8. Inspect the underside of the sink for any remaining parts of the Ez Mount sink flange kit. If there are any remaining parts, remove them carefully using a screwdriver or pliers. To remove the Ez Mount gasket, use a putty knife to gently pry it away from the sink. If the gasket is stuck to the sink, use a solvent to loosen it.
9. Clean the surface of the countertop where the flange will be installed.
10. Apply a bead of silicone sealant around the edge of the flange.
11. Press the flange into place on the countertop.
12. Tighten the screws that secure the flange to the countertop.
13. Allow the silicone sealant to dry for 24 hours before using the sink.
Reconnect the Plumbing
1. Start by removing the old flange kit from the sink. Twist the flange counterclockwise to detach it from the sink.
2. Clean the surface of the sink and the underside of the flange with a damp cloth.
3. Apply a bead of plumber’s putty around the base of the new flange.
4. Position the new flange over the drain hole and press it into place.
5. Tighten the flange using the supplied screws or bolts.
Reconnect the Drainpipe
1. Measure and cut a piece of PVC pipe to fit between the flange and the P-trap.
2. Apply a thin layer of PVC glue to the ends of the pipe and insert it into the flange and the P-trap.
3. Tighten the nuts on the P-trap to secure it in place.
Reconnect the Water Supply Line
1. Measure and cut a piece of flexible water supply line to fit between the faucet and the shut-off valves.
2. Attach one end of the supply line to the shut-off valve and the other end to the faucet.
3. Tighten the nuts on the supply lines to secure them in place.
Test the Connections
1. Turn on the water supply and check for leaks.
2. If any leaks are found, tighten the nuts or replace the washers.
3. Once you are satisfied that there are no leaks, turn off the water supply and move on to the next step.
Finish the Installation
Once the EZ Mount Sink Flange Kit is secured, it’s time to finish the installation by connecting the plumbing and faucet. Here are the steps involved:
1. Plumbing connections
Connect the water supply lines to the hot and cold water shut-off valves beneath the sink. Ensure that the connections are watertight by using plumber’s tape or pipe dope on the threads.
2. Drain plumbing
Connect the drainpipe to the sink drain flange. Tighten the slip nut and washer to form a watertight seal. If necessary, use plumber’s putty or silicone sealant around the joint to prevent leaks.
3. Faucet installation
Insert the faucet into the pre-installed holes on the sink or countertop. Secure it by tightening the mounting nuts from underneath. Connect the water supply lines to the faucet’s hot and cold water inlets.
4. Test the installation
Turn on the water supply and check for leaks at all connections. If any leaks are detected, tighten the connections or apply additional sealant as needed.
5. Clean up
Remove any excess sealant or debris from the sink, countertop, and surrounding area. Clean the sink and faucet thoroughly with a damp cloth.
6. Enjoy your new sink
The EZ Mount Sink Flange Kit provides a secure and easy-to-install solution for mounting your sink. By following these detailed instructions, you can ensure a successful installation and enjoy years of worry-free use.
7. Table summarizing installation steps:
| Step | Description |
|---|---|
| 1 | Connect water supply lines to shut-off valves |
| 2 | Connect drainpipe to sink drain flange |
| 3 | Install faucet and connect water supply lines |
| 4 | Test installation for leaks |
| 5 | Clean up excess sealant and debris |
| 6 | Enjoy your newly installed sink |
How to Remove an EZ Mount Sink Flange Kit
Removing an EZ Mount sink flange kit is a relatively easy task that can be completed in a few simple steps. Here’s a step-by-step guide to help you through the process:
- Disconnect the water supply lines.
- Loosen the nuts that hold the flange to the sink.
- Remove the flange from the sink.
- Clean the area where the flange was installed.
- Install a new flange.
Here are some additional tips that may be helpful:
- If the nuts are corroded, you may need to use a penetrating oil to loosen them.
- Be careful not to overtighten the nuts when you install the new flange.
- If you are having difficulty removing the flange, you may need to contact a professional plumber for assistance.
People Also Ask About How to Remove an EZ Mount Sink Flange Kit
How do I remove a stuck EZ Mount sink flange?
If the EZ Mount sink flange is stuck, you may need to use a penetrating oil to loosen it. Apply the penetrating oil to the nuts that hold the flange to the sink and let it sit for a few minutes. Then, try to loosen the nuts with a wrench.
Can I remove an EZ Mount sink flange without removing the sink?
Yes, you can remove an EZ Mount sink flange without removing the sink. However, it may be easier to remove the sink if you need to access the flange from the bottom.
How do I install a new EZ Mount sink flange?
To install a new EZ Mount sink flange, first clean the area where the flange will be installed. Then, apply a bead of silicone sealant to the bottom of the flange. Place the flange over the sink drain and tighten the nuts that hold it in place.
