Nest Doorbells are a convenient and effective way to keep an eye on your home, but there may come a time when you need to remove the device. Whether you’re moving, replacing the doorbell, or simply experiencing technical difficulties, removing a Nest Doorbell is a straightforward process that can be completed in a few simple steps. This comprehensive guide will provide you with clear instructions on how to safely and efficiently detach your Nest Doorbell from its mounting plate, ensuring a seamless removal experience.
Before embarking on the removal process, it is crucial to ensure your safety by taking precautionary measures. Begin by turning off the power to the doorbell at your home’s circuit breaker panel. This step is essential to prevent any electrical hazards during the removal process. Once the power is disconnected, you can proceed to the physical removal of the Nest Doorbell. Carefully remove the faceplate by pressing the release button located at the bottom of the device. This will expose the mounting plate and the wires connected to the doorbell.
Proceed to disconnect the wires from the mounting plate. Note that the wiring configuration may vary depending on the model of your Nest Doorbell. Typically, there will be two wires, one for power and one for data. Use a small screwdriver to loosen the screws holding the wires in place and gently pull them out of the terminals. Once the wires are disconnected, you can carefully remove the mounting plate from the wall. Avoid pulling on the wires excessively, as this could damage the doorbell or the wiring. With the mounting plate detached, you have successfully removed your Nest Doorbell.
Safely Disconnecting Power and Wiring
Turn Off Power
Begin by ensuring the safety of your working environment. Locate the breaker panel or fuse box that supplies electricity to the doorbell. Once identified, flip the corresponding switch or remove the fuse to cut off power to the device.
As a precautionary measure, it’s advisable to use a non-contact voltage tester to confirm that the power has been successfully disconnected before proceeding further.
Disconnect Wiring
Now, proceed to the doorbell itself. Using a screwdriver or drill, carefully unscrew the screws on the device’s faceplate, allowing you to access the wiring beneath.
Each wire will typically have a different color to indicate its function. **Note:** Before disconnecting any wires, take a photograph for future reference to ensure proper reconnection.
Gently pull the wires straight out of the terminal block. If the wires are held in place by screws, loosen the screws first. Once all wires are disconnected, carefully pull the doorbell away from the mounting bracket.
Removing the Doorbell Bracket
To remove the doorbell bracket, follow these detailed steps:
1. Power Down the Doorbell
Before you begin, ensure that the doorbell is powered down. Locate the small black button on the back of the doorbell and press and hold it for 10 seconds until the LED light turns off.
2. Detach the Faceplate
Next, gently push down on the faceplate from the top and pull it straight towards you to detach it from the bracket. Be careful not to apply excessive force.
3. Remove the Screws
Locate the two screws securing the bracket to the wall or doorframe. Using a screwdriver, carefully unscrew both screws.
4. Pull Down the Bracket
Once the screws are removed, gently pull the bracket straight down to detach it from the mounting surface. Be cautious not to pull it too hard or at an angle, as this could damage the wires or the wall.
5. Disconnect the Wires
If the bracket has wires connected to it, carefully disconnect them by pressing the small tabs on the wire terminals and pulling the wires out. Label the wires for easy reconnection later.
6. Remove the Bracket
With the wires disconnected, the bracket is now free to be removed from the wall. Carefully lift it off the mounting surface.
| Step | Action |
|---|---|
| 1 | Power down the doorbell. |
| 2 | Detach the faceplate by pushing down and pulling straight towards you. |
| 3 | Remove the two screws securing the bracket to the wall. |
| 4 | Pull the bracket straight down to detach it. |
| 5 | Disconnect the wires if any. |
| 6 | Remove the bracket from the wall. |
Detaching the Doorbell from the Bracket
### Step 1: Disconnect the Wiring
Before handling the doorbell, ensure all electrical power to the device is disconnected at the circuit breaker. Use a non-contact voltage tester or a multimeter to confirm that there is no voltage present on the doorbell wires.
### Step 2: Unscrew the Mounting Screws
Locate the two mounting screws that hold the doorbell to the bracket. These screws are typically located on either side of the doorbell’s base. Using a screwdriver, carefully unscrew both screws counterclockwise until they are completely removed.
### Step 3: Remove the Doorbell from the Bracket
Once the mounting screws are removed, gently pull the doorbell straight toward you to remove it from the bracket. Some models may have a locking tab that needs to be disengaged before the doorbell can be detached. If you encounter any resistance, check for any snagged wires or connections.
### Step 4: Inspect the Wires and Bracket
After removing the doorbell, inspect the wires and bracket for any damage or corrosion. If any wires are damaged, they should be replaced or repaired before reattaching the doorbell. Ensure the bracket is secure and not loose or damaged.
Unscrewing the Faceplate and Speaker
To unscrew the faceplate and speaker, you’ll need a Philips #1 screwdriver.
1. Remove the two screws that are located at the bottom of the faceplate.
2. Carefully lift the faceplate off of the doorbell.
3. Disconnect the speaker wire from the back of the faceplate.
4. Unscrew the four screws that are holding the speaker in place.
5. Carefully lift the speaker out of the doorbell.
| Screw Size | Location |
|---|---|
| Phillips #1 | Bottom of the faceplate |
| Phillips #1 | Holding the speaker in place |
Removing the Main Module
Step 1: Disconnect Power
Before you start, ensure the power to the Nest Doorbell is disconnected. Locate the circuit breaker or fuse box that supplies power to the doorbell and turn it off.
Step 2: Remove Trim Plate
Using a screwdriver, remove the two screws on the bottom of the trim plate. Once the screws are removed, gently pull the trim plate straight towards you to detach it.
Step 3: Unscrew Main Module
Once the trim plate is removed, you will see the main module of the Nest Doorbell. Use a screwdriver to unscrew the two screws on the left and right sides of the module.
Step 4: Disconnect Wires
Gently pull the module away from the mounting bracket to expose the wire terminals. Use a pair of pliers to squeeze the release tabs on the wire terminals and disconnect the wires.
Step 5: Remove the Module
With the wires disconnected, you can now remove the main module from the mounting bracket. To do this, gently pull straight down on the module until it releases.
If there is a wedge installed behind the Nest Doorbell, you may need to remove it before pulling the module down. To do this, carefully pry the wedge loose using a flathead screwdriver.
Table of Tools You May Need:
| Tool | Purpose |
|---|---|
| Screwdriver | Removing screws |
| Pliers | Disconnecting wires |
| Flathead screwdriver | Prying loose wedge (if applicable) |
Cleaning Up Any Remaining Wires or Debris
After removing your Nest Doorbell, you may be left with some stray wires or debris. Here’s how to clean them up:
Disconnect the wires
If there are any wires connected to your Nest Doorbell, be sure to disconnect them before proceeding. Use a pair of pliers or wire cutters to carefully cut the wires. Be careful not to damage the wires or the surrounding area.
Remove the debris
Once the wires are disconnected, you can remove any debris that is left behind. This may include dust, dirt, or small pieces of wire. Use a vacuum cleaner or a damp cloth to clean up the debris.
Inspect the area
Once the debris is removed, take a close look at the area where the Nest Doorbell was mounted. Make sure that there is no damage to the wall or the surrounding area. If you find any damage, be sure to repair it before installing a new doorbell.
Fill any holes
If you removed the Nest Doorbell from a hole in the wall, you will need to fill the hole. You can use a putty knife or caulk gun to fill the hole. Be sure to smooth out the filler so that it is flush with the wall.
Paint or touch up the area
If you filled any holes or made any repairs, you may want to paint or touch up the area to make it look new again. Use a paint that matches the color of your wall.
Additional Tips
Here are some additional tips for cleaning up after removing your Nest Doorbell:
- Be careful not to damage the wires or the surrounding area when disconnecting the wires.
- Use a vacuum cleaner or a damp cloth to clean up any debris.
- Inspect the area where the Nest Doorbell was mounted for any damage.
- Fill any holes with putty or caulk.
- Paint or touch up the area to make it look new again.
**Removing the Nest Doorbell**
To remove the Nest Doorbell from its mounting plate, follow these steps:
- Press the release button on the bottom of the Doorbell.
- Pull the Doorbell straight down to disconnect it from the mounting plate.
**Restoring the Doorbell to Factory Settings**
If you need to reset your Doorbell to its factory settings, follow these steps:
- Disconnect the Doorbell from power by removing its battery or turning off its circuit breaker.
- Press and hold the reset button on the back of the Doorbell for 10 seconds.
- Release the button and wait for the Doorbell to restart.
- Once the Doorbell has restarted, reconnect it to power.
- The Doorbell will now be restored to its factory settings and you will need to set it up again.
**Removing the Doorbell from Your Account**
If you need to remove the Doorbell from your Google Account, follow these steps:
- Open the Nest app on your phone.
- Tap the Settings icon in the top right corner of the screen.
- Tap the Devices tab.
- Select the Doorbell you want to remove.
- Tap the Remove button.
- Confirm that you want to remove the Doorbell.
**Deleting the Doorbell from Your Home**
If you need to delete the Doorbell from your Google Home account, follow these steps:
- Open the Google Home app on your phone.
- Tap the Settings icon in the top right corner of the screen.
- Tap the Home tab.
- Select the home you want to remove the Doorbell from.
- Tap the Devices tab.
- Select the Doorbell you want to delete.
- Tap the Remove button.
- Confirm that you want to delete the Doorbell.
Disconnect the Doorbell from the Base
Gently pull down on the doorbell to detach it from its base. If it’s difficult to remove, use a small flathead screwdriver or plastic pry tool to gently pry it off while holding the base steady.
Remove the Base from the Wall
Use a Phillips head screwdriver to unscrew the two screws securing the base to the wall. Pull the base straight down to detach it.
Disconnect the Wires from the Base
Identify the two wires connected to the back of the base. Squeeze the tabs on the wire connectors and pull the wires straight out. Note the color coding of the wires, as you’ll need them for reconnecting later.
Remove the Mounting Plate (Optional)
If you installed a mounting plate for a more flush fit, use a screwdriver to remove the two screws securing it to the wall. Pull the plate straight down to remove it.
Troubleshooting Common Removal Issues
The Doorbell Won’t Detach from the Base
Ensure that the doorbell is not obstructed by dirt or debris. If it still won’t release, use a small flathead screwdriver to gently pry it off at the corners.
There are Multiple Wires Connected to the Base
If you encounter more than two wires, you may have a doorbell chime or other accessory connected to the system. Refer to the Nest Doorbell installation guide or consult with an electrician for further assistance.
The Base is Stuck on the Wall
Inspect the screws to ensure they are completely removed. If the base is still stuck, apply gentle pressure with a plastic pry tool or a wooden shim, working around the edges until it comes loose.
| Difficulty | Troubleshooting Step |
| Unable to detach doorbell from base | Use a small flathead screwdriver to gently pry it off. |
| Multiple wires connected to base | Refer to installation guide or consult an electrician. |
| Base stuck on wall | Apply gentle pressure with a plastic pry tool or wooden shim. |
Safety Precautions for Removing Nest Doorbells
1. Shut Off Power
Turn off the power to the doorbell by flipping the circuit breaker or removing the fuse.
2. Use Proper Tools
Gather necessary tools like a screwdriver, pliers, and a ladder (if needed).
3. Protect Eyes and Hands
Wear safety glasses and gloves to prevent injury from flying particles.
4. Ensure Proper Footing
Use a sturdy ladder if needed and maintain proper balance.
5. Disconnect Wires
Use pliers to carefully remove the wires connected to the doorbell.
6. Remove Mounting Screws
Unscrew the mounting screws holding the doorbell in place.
7. Gently Pull Away
Gently pull the doorbell away from the mounting surface.
8. Inspect for Damage
Check the doorbell and wires for any damage or loose connections.
9. Disconnect the Battery (For Battery-Powered Models)
For battery-powered Nest Doorbells, carefully remove the battery compartment and disconnect the battery. Note the orientation of the battery for correct reinstallation.
How to Remove Nest Doorbell
Removing a Nest Doorbell is a simple process that can be completed in just a few minutes. To remove your Nest Doorbell, follow these steps:
- Gently pull the bottom of the doorbell camera forward.
- Push the doorbell camera down and away from the mounting plate.
- Disconnect the wires from the back of the doorbell camera.
- Remove the mounting plate from the wall.
Once you have removed the Nest Doorbell, you can install a new one or simply leave the space empty. If you are installing a new doorbell, be sure to follow the manufacturer’s instructions for installation.
People Also Ask
How do I reset my Nest Doorbell?
To reset your Nest Doorbell, press and hold the setup button on the back of the device for 10 seconds. The doorbell will flash white and then restart.
How do I change the batteries in my Nest Doorbell?
To change the batteries in your Nest Doorbell, remove the two screws on the bottom of the device and lift the front panel up. Replace the old batteries with two new CR123A batteries. Replace the front panel and secure it with the screws.
How do I troubleshoot my Nest Doorbell?
If you are having problems with your Nest Doorbell, there are a few things you can try to troubleshoot the issue. First, check the batteries and make sure they are properly installed. Next, try restarting the doorbell by pressing and holding the setup button for 10 seconds. If you are still having problems, contact Nest support.
