Replacing your car battery is a relatively simple task that can be completed in about 30 minutes. However, it’s important to follow the correct steps to avoid any damage to your vehicle. In this article, we’ll walk you through the process of replacing the battery in a 2020 Hyundai Kona.
Before you begin, you’ll need to gather a few tools: a new battery, a wrench, and a pair of gloves. You should also park your car in a safe location and turn off the engine. Once you have your tools and your car is prepared, you can begin the replacement process.
The first step is to locate the battery. The battery in the 2020 Hyundai Kona is located in the engine compartment, on the passenger side. Once you’ve located the battery, you’ll need to disconnect the negative terminal. To do this, use the wrench to loosen the nut that’s holding the terminal in place. Once the nut is loose, you can remove the terminal from the battery. Next, you’ll need to disconnect the positive terminal. To do this, follow the same steps as you did for the negative terminal.
Preparation and Safety Precautions
General Preparation:
Before attempting to replace your Hyundai Kona’s battery, ensure you have the necessary tools and materials, including a new battery, wrench, 10mm socket, and safety glasses. Park the vehicle on a flat, stable surface, and engage the parking brake to prevent it from rolling.
Safety Precautions:
Battery replacement involves working with electrical components that can cause injury. Observe the following safety precautions:
- Disconnect the negative terminal first, then the positive terminal. This prevents potential short circuits and sparks.
- Wear safety glasses to protect your eyes from battery acid and debris.
- Keep a fire extinguisher nearby in case of an accident.
- Avoid touching the battery terminals directly with bare hands. Use gloves or a cloth.
Disconnecting the Negative Terminal
The second step in replacing your Kona’s car battery is to disconnect the negative terminal. The negative terminal is typically black and has a negative (-) sign. To disconnect the negative terminal, you will need a 10mm wrench or socket. Follow these steps to disconnect the negative terminal safely:
Step 1: Locate the Negative Terminal
Open the hood of your Kona and locate the battery. The negative terminal is usually located on the left-hand side of the battery and is marked with a negative (-) sign.
Step 2: Loosen the Negative Terminal Nut
Using a 10mm wrench or socket, loosen the nut that secures the negative terminal to the battery. Do not remove the nut completely at this point.
Step 3: Lift the Negative Terminal Off the Battery
Once the nut is loose, lift the negative terminal straight up off the battery post. Be careful not to touch the positive terminal with the negative terminal, as this could cause a short circuit.
Step 4: Inspect the Negative Terminal
Inspect the negative terminal for any damage or corrosion. If there is any damage or corrosion, you will need to replace the negative terminal before proceeding.
| Tool | Size |
|---|---|
| Wrench or socket | 10mm |
Removing the Battery Hold-Down Clamp
The battery hold-down clamp is a metal bracket that secures the battery in place. To remove it, you’ll need a 10mm socket wrench or a 10mm spanner.
1.Locate the battery hold-down clamp. It’s usually located on the top of the battery, near the terminals.
2.Loosen the bolts that hold the clamp in place. Do not remove the bolts completely.
3.Lift the clamp off the battery.
4.Carefully lift the battery out of the battery tray. Be careful not to drop the battery, as it is heavy.
| Tools you will need: | 10mm socket wrench or 10mm spanner |
| Estimated time: | 10 minutes |
| Difficulty level: | Easy |
Lifting the Old Battery Out
Once you have disconnected the terminals and loosened the hold-down bolts, it’s time to lift the old battery out of the Kona. This can be a bit tricky, as the battery is heavy and can be awkward to handle. Here are some tips for lifting the battery out safely:
1. Get a good grip and lift with your legs. Do not bend over to lift the battery, as this can put strain on your back. Instead, squat down and grip the battery with both hands. Use your legs to lift the battery up and out of the compartment.
2. Be careful not to drop the battery. This could damage the battery or your vehicle. If you are having trouble lifting the battery, ask for help from a friend or family member.
3. Place the old battery in a safe place. Do not leave it on the ground, as this could create a hazard. You can place the old battery in a cardboard box or on a piece of wood.
4. Dispose of the old battery properly. Batteries contain hazardous materials, so it is important to dispose of them properly. You can take your old battery to an auto parts store or recycling center.
5. **Safety precautions while lifting the battery:**
| Safety Measure | Reason |
|---|---|
| Wear gloves and safety glasses. | Battery acid can cause burns and eye damage. |
| Do not smoke or use open flames near the battery. | Batteries can produce hydrogen gas, which is flammable. |
| Avoid contact with your eyes or skin. | Battery acid can cause irritation or burns. |
Installing the New Battery
1. Disconnect the negative terminal. Using a 10mm wrench, loosen the nut on the negative terminal of the old battery. Remove the nut and washer, then lift off the negative terminal.
2. Disconnect the positive terminal. Using the same wrench, loosen the nut on the positive terminal of the old battery. Remove the nut and washer, then lift off the positive terminal.
3. Remove the old battery. Grab the old battery by the handles and lift it out of the car. Be careful not to drop it, as it is heavy.
4. Clean the battery terminals. Use a wire brush to clean the terminals on the old battery and the cables on the car. This will ensure a good connection with the new battery.
5. Install the new battery. Place the new battery in the car, making sure that the terminals are facing the correct direction.
6. Connect the positive terminal. Place the positive terminal on the positive terminal of the new battery. Tighten the nut and washer using the wrench.
| Connecting the Negative Terminal |
|
Place the negative terminal on the negative terminal of the new battery. |
|
Tighten the nut and washer using the wrench. |
|
Check the connections to ensure they are tight. |
7. Tighten the hold-down bolts. Using the wrench, tighten the hold-down bolts that secure the battery in place.
8. Check the battery connections. Ensure all connections are tight and secure.
Connecting the Positive Terminal
Once the negative terminal is reconnected, it’s time to connect the positive terminal. This process should be similar to connecting the negative terminal. Make sure the positive terminal is clean and free of corrosion before connecting it to the battery. The positive terminal is usually marked with a red cable or a positive sign (+). Once the positive terminal is connected, tighten the nut or bolt that secures it. Use the torque wrench to apply the proper amount of torque to the nut or bolt. The correct torque for the positive terminal can be found in the owner’s manual for your vehicle.
After the positive terminal is connected, double-check all of the connections to make sure they are tight. Positive terminal should be the last connection. Start the engine to make sure the battery is working properly.
Tightening the Terminal Nuts
When tightening the terminal nuts, it is important to use a torque wrench to apply the correct amount of torque. The correct torque for the terminal nuts can be found in the owner’s manual for your vehicle. Overtightening the terminal nuts can damage the battery or the terminals.
| Tool | Use |
|---|---|
| 10mm socket | To remove and install the battery terminals |
| 10mm wrench | To tighten the battery terminals |
| Torque wrench | To apply the correct amount of torque to the battery terminals |
| Battery terminal cleaner | To clean the battery terminals and posts |
| Safety glasses | To protect your eyes from battery acid |
Connecting the Negative Terminal
The next step is to connect the negative terminal. This is the black cable, and it should be connected to the negative terminal on the new battery. Make sure that the connection is tight, but do not overtighten it. Once the negative terminal is connected, you can start the car.
If you are not comfortable connecting the battery yourself, you can always take your car to a mechanic. They will be able to safely and quickly connect the battery for you.
Here are some additional tips for connecting the negative terminal:
- Make sure that the negative terminal is clean and free of corrosion.
- Use a wrench to tighten the connection, but do not overtighten it.
- Double-check the connection to make sure that it is tight.
- Start the car to make sure that the connection is working properly.
By following these steps, you can safely and easily connect the negative terminal on your Hyundai Kona 2020.
| Step | Description |
|---|---|
| 1 | Locate the negative terminal on the new battery. |
| 2 | Clean the negative terminal on the battery and the car. |
| 3 | Connect the negative cable to the negative terminal on the battery. |
| 4 | Tighten the connection using a wrench. |
| 5 | Double-check the connection to make sure that it is tight. |
| 6 | Start the car to make sure that the connection is working properly. |
Safety Precautions
Before beginning the battery replacement procedure, ensure the safety of yourself and your vehicle by adhering to the following precautions:
- Park the vehicle on a flat, stable surface and engage the parking brake.
- Turn off the engine and allow the vehicle to cool down.
- Disconnect the negative terminal of the battery using a wrench or socket.
- Wear gloves and eye protection to avoid contact with battery acid.
Locating the Battery
The battery in the Hyundai Kona 2020 is located in the engine compartment, typically near the firewall or the front of the vehicle.
Removing the Old Battery
Once you have located the battery, follow these steps to remove the old battery:
- Using a wrench or socket, disconnect the positive terminal of the battery.
- Remove the battery hold-down clamp or bracket.
- Carefully lift the old battery out of its compartment.
- Clean the battery terminals and the battery compartment using a wire brush or terminal cleaner.
Installing the New Battery
Before installing the new battery, ensure it is the correct size and type for your vehicle. Follow these steps to install the new battery:
- Place the new battery in the compartment, ensuring the terminals align with the battery cable connectors.
- Install the battery hold-down clamp or bracket.
- Connect the positive terminal of the battery using a wrench or socket.
- Tighten the battery terminals by hand, then use a wrench or socket to ensure a secure connection.
Starting the Vehicle and Reconfiguring Settings
Starting the Vehicle
Once the new battery is installed, start the vehicle and let it run for a few minutes to charge the battery.
Reconfiguring Settings
After replacing the battery, you may need to reconfigure certain vehicle settings, such as the clock, radio presets, and climate control settings. Consult your vehicle’s owner’s manual for specific instructions on reconfiguring settings.
How To Replace Car Battery Kona 2020
Replacing the car battery on a 2020 Hyundai Kona is a relatively simple task that can be completed in a few steps. Here’s a quick guide on how to do it:
1. Safety first: Park the car in a safe place, put on safety glasses, and turn off the engine.
2. Locate the battery: The battery is usually located under the hood, secured with a metal bracket.
3. Disconnect the negative terminal: Using a wrench, loosen the nut on the negative (black) terminal, and lift the terminal off the battery post.
4. Disconnect the positive terminal: Repeat step 3 for the positive (red) terminal.
5. Remove the battery hold-down bracket: Locate the bolt or nut holding the battery in place, and unfasten it.
6. Lift out the old battery: Carefully lift the old battery out of the compartment.
7. Place the new battery: Lower the new battery into the compartment, making sure the terminals are facing the correct direction.
8. Connect the positive terminal: Place the positive (red) terminal on the battery post and tighten the nut.
9. Connect the negative terminal: Repeat step 8 for the negative (black) terminal.
10. Tighten the battery hold-down bracket: Secure the battery in place by tightening the bolt or nut on the bracket.
11. Start the engine: Start the engine to check if the new battery is working properly.
People Also Ask
How long does it take to replace a car battery on a 2020 Hyundai Kona?
It usually takes around 30 minutes to replace the battery on a 2020 Hyundai Kona.
What is the cost of replacing a car battery on a 2020 Hyundai Kona?
The cost of replacing a battery on a 2020 Hyundai Kona can vary depending on the type of battery you choose and where you get it replaced. However, you can expect to pay between $100 and $200 for the battery and labor.
Is it safe to replace a car battery on a 2020 Hyundai Kona yourself?
Replacing the battery on a 2020 Hyundai Kona is a relatively simple task, and it is safe to do it yourself if you have some basic mechanical skills. However, if you are not comfortable working on your car, it is best to take it to a mechanic.
