Disassembling a Vornado EH1 00115 can be a straightforward task. However, it’s crucial to approach the process with caution, using the appropriate tools and following specific steps to avoid damaging the appliance. Whether you’re replacing a faulty component or thoroughly cleaning the unit, understanding the proper disassembly procedure is essential. In this article, we’ll guide you through the steps involved in taking apart a Vornado EH1 00115, providing clear instructions and safety precautions to ensure a successful disassembly.
Before commencing disassembly, gather the necessary tools, including a Phillips head screwdriver, a flathead screwdriver, and a pair of needle-nose pliers. Disconnect the appliance from the power source and allow it to cool completely. Locate the screws securing the base assembly to the fan housing. Carefully remove these screws and set them aside in a safe place. Next, gently lift the base assembly away from the fan housing, being cautious not to damage any wires or components. Disconnect the electrical connectors by pressing on the release tabs and carefully pulling the connectors apart.
With the base assembly removed, you can proceed to disassemble the fan housing. Locate the screws securing the fan motor to the housing and remove them. Carefully lift the fan motor out of the housing, taking care to avoid dislodging any wires or components. Next, remove the screws securing the fan blades to the fan motor and carefully detach the blades. Continue disassembling the fan housing by removing any additional screws or fasteners that may be present. Once all components are separated, inspect them thoroughly for any damage or wear. If necessary, replace any faulty parts before reassembling the appliance.
Removing the Base Plate
To take apart the Vornado EH1-00115, you must first remove the base plate. This can be done by following these steps:
Step 1: Unplug the Fan
Before you begin, ensure the fan is unplugged from the power outlet. This is a crucial safety precaution to prevent any electrical accidents.
Step 2: Locate the Screws
Flip the fan upside down and locate the four screws securing the base plate to the fan’s housing. These screws are typically Phillips head screws and can be removed using a standard screwdriver.
Step 3: Remove the Screws
Using the screwdriver, carefully remove all four screws. Be sure to hold onto the screws as you remove them, as you will need them later to reassemble the fan.
Step 4: Lift Off the Base Plate
Once all four screws have been removed, gently lift the base plate away from the fan’s housing. The base plate should come off easily without any resistance.
Step 5: Inspect the Base Plate
Once the base plate has been removed, inspect it for any damage or loose wires. If any damage is found, it is advisable to replace the base plate before reassembling the fan.
Disassembling the Column Shaft
To disassemble the column shaft, follow these steps:
1. Separate the Shaft into Two Pieces
To separate the column shaft into two pieces, rotate the shaft slowly until the slots in the lower shaft align with the clips on the upper shaft. Pull the upper shaft straight up to detach it from the lower shaft.
2. Detach the Upper Shaft from the Fan Head
To detach the upper shaft from the fan head, follow these steps:
- Locate the two screws on the front of the fan head that hold the upper shaft in place.
- Loosen the screws, but do not remove them completely.
- Carefully lift the fan head up and away from the upper shaft.
3. Remove the Column Shaft from the Base
To remove the column shaft from the base, follow these steps:
- Locate the three screws on the bottom of the base that hold the column shaft in place.
- Remove the screws.
- Carefully lift the column shaft straight up and away from the base.
Detaching the Motor Housing
Once the fan blade has been removed, it’s time to detach the motor housing. The motor housing is the central part of the fan, containing the motor and other electrical components. To detach the motor housing, follow these steps:
- Locate the screws: There are typically four screws holding the motor housing in place. These screws are usually located at the back or bottom of the fan.
- Remove the screws: Using a screwdriver, carefully remove the screws. Be sure to hold onto the screws as you remove them.
- Gently lift the motor housing: Once the screws are removed, gently lift the motor housing away from the base of the fan. The motor housing may be slightly stuck, so you may need to use a little force to detach it.
With the motor housing detached, you can now access the motor and other electrical components for repair or replacement.
Accessing the Motor
Once the motor housing is detached, you can access the motor. The motor is biasanya located at the bottom of the motor housing. To access the motor, follow these steps:
- Disconnect the motor wires: Before handling the motor, disconnect the motor wires from the terminal block. The terminal block is usually located near the motor.
- Remove the motor mounting screws: There are typically two or three screws holding the motor in place. These screws are usually located on the sides of the motor.
- Lift the motor out: Once the mounting screws are removed, gently lift the motor out of the motor housing.
With the motor removed, you can now inspect it for any damage or wear. If necessary, you can replace the motor with a new one.
Removing the Blower Wheel
Now that you’ve safely removed the front cover and housing, it’s time to tackle the blower wheel. Here’s a step-by-step guide:
1. Unplug the Wires
Before you touch the blower wheel, disconnect the wires connected to it. Use a pair of needle-nose pliers to gently pull the connectors off the terminals.
2. Remove the Fasteners
Locate the screws or bolts holding the blower wheel in place. Depending on the model, there may be two or more fasteners. Use a suitable screwdriver or wrench to remove them.
3. Detach the Blower Wheel
With the fasteners removed, carefully pull the blower wheel straight out of the unit. It may be necessary to wiggle it slightly to loosen it.
4. Clean and Inspect
Take the blower wheel to a clean and well-lit area. Use a soft brush or cloth to gently remove any dust or debris accumulated on the blades. Thoroughly inspect the blower wheel for any damage or wear. Look for cracks, chips, or any other signs of compromise. If any damage is found, it’s recommended to replace the blower wheel with a new one.
| Tool | Description |
|---|---|
| Needle-nose pliers | For disconnecting wires |
| Screwdriver or wrench | For removing fasteners |
| Soft brush or cloth | For cleaning the blower wheel |
Accessing the Motor
To access the motor, you will need to remove the base of the fan.
1. Turn the fan upside down and locate the four screws that hold the base in place.
2. Use a screwdriver to remove the screws.
3. Gently lift the base off of the fan.
4. The motor is located at the bottom of the fan.
To remove the motor, you will need to disconnect the wires that are connected to it.
| Wire Color | Terminal |
|---|---|
| Black | L |
| White | N |
| Green | Ground |
5. Use a pair of pliers to disconnect the wires from the motor.
6. Once the wires are disconnected, you can lift the motor out of the fan.
Replacing the Bearings
1. Remove the Fan Head: Unplug the fan and remove the fan head by grasping it firmly and pulling it straight up off the base.
2. Detach the Motor Housing: Use a Phillips head screwdriver to remove the screws securing the motor housing to the base. Lift the motor housing off the base, taking care not to damage the wires.
3. Access the Bearings: Locate the two bearings on the motor shaft. They are typically held in place by a metal clip or a rubber grommet.
4. Remove the Old Bearings: Using a small flathead screwdriver or a pair of needle-nose pliers, carefully pry the metal clip or remove the rubber grommet to release the old bearings.
5. Clean the Area: Before installing the new bearings, thoroughly clean the area where they will be placed. Remove any dirt, dust, or debris.
6. Install the New Bearings: Align the new bearings on the motor shaft and gently slide them into place. Ensure that the bearings are properly seated and that the metal clip or rubber grommet is securely fastened to hold them in place.
7. Reassemble the Fan: Reattach the motor housing to the base and secure it with the screws. Place the fan head back on the base and plug the fan back in.
Cleaning and Lubricating Components
To ensure the optimal performance and longevity of your Vornado EH1 00115, proper cleaning and lubrication of its components is essential. Here’s a detailed guide to assist you in this process:
Components to be Lubricated:
| Component | Frequency |
|---|---|
| Motor Bearings | Annually |
| Oscillation Mechanism | Semi-annually |
| Fan Hub | Quarterly |
Tools You’ll Need:
- Phillips head screwdriver
- Flathead screwdriver
- Vacuum cleaner
li>Lubricant (e.g., sewing machine oil, WD-40)
Steps to Lubricate Components:
1.
Remove the front cover: Use a Phillips head screwdriver to remove the screws holding the front cover. Lift the cover up and away from the unit.
2.
Locate motor bearings: Identify the motor bearings, which are usually located at the base of the fan assembly.
3.
Apply lubricant: Apply a few drops of lubricant to the bearings using the oil can or syringe. Avoid over-lubricating.
4.
Lubricate oscillation mechanism: Find the oscillation mechanism, which is responsible for the fan’s side-to-side movement. Apply lubricant to the gears and moving parts.
5.
Lubricate fan hub: Locate the fan hub, which is the central part of the fan assembly. Apply a small amount of lubricant to the hub and its contact points with the blades.
6.
Reassemble the unit: Place the front cover back on the unit and secure it with the screws.
7.
Test the fan: Plug in the fan and turn it on to ensure it’s operating smoothly and quietly. If any unusual noises or vibrations occur, re-check the lubrication or seek professional assistance.
Disassembling The Vornado EH1-00115
1. Unplug the Vornado EH1-00115 from the power outlet.
2. Remove the back grill by unscrewing the four screws that hold it in place.
3. Disconnect the power cord from the motor.
4. Remove the two screws that hold the motor in place and lift the motor out of the unit.
5. Remove the two screws that hold the fan blades in place and remove the fan blades.
6. Remove the two screws that hold the front grill in place and remove the front grill.
7. The Vornado EH1-00115 is now disassembled.
Reassembling The Vornado EH1-00115
1. Insert the fan blades into the motor and secure them with the two screws.
2. Place the motor into the unit and secure it with the two screws.
3. Connect the power cord to the motor.
4. Place the back grill on the unit and secure it with the four screws.
5. Plug the Vornado EH1-00115 into the power outlet.
6. The Vornado EH1-00115 is now reassembled.
Troubleshooting
If you are having trouble reassembling the Vornado EH1-00115, check the following:
* Make sure that all of the screws are tightened securely.
* Make sure that the power cord is connected securely to the motor.
* Make sure that the fan blades are inserted correctly into the motor.
* If you are still having trouble, you can contact Vornado Customer Service for assistance.
| Part | Quantity |
|---|---|
| Screws | 6 |
| Fan blades | 2 |
| Motor | 1 |
| Power cord | 1 |
| Back grill | 1 |
| Front grill | 1 |
Troubleshooting Common Issues
The fan is not turning on
Check if the power cord is securely plugged into both the fan and the electrical outlet. Also, check if the circuit breaker or fuse for the electrical outlet has tripped.
The fan is making a rattling noise
A rattling noise is usually caused by a loose screw or bearing. Check all the screws on the fan and tighten any that are loose. If the noise persists, contact Vornado customer service.
The fan is wobbling
A wobbling fan can be caused by a variety of issues, including a bent fan blade, a loose fan base, or uneven flooring. Check the fan blade for any bends or cracks and straighten it if necessary. Tighten the nut that secures the fan base to the column. If the flooring is uneven, try placing the fan on a level surface.
The fan is not oscillating
Check if the oscillation switch is turned on. If it is on, try unplugging the fan for a few seconds and then plugging it back in. If the fan still does not oscillate, contact Vornado customer service.
The fan is not blowing strong enough
Check if the air filter is dirty. A dirty filter can restrict airflow and reduce the fan’s performance. Clean the filter according to the manufacturer’s instructions.
The remote control is not working
Check if the batteries in the remote control are dead. Replace the batteries with new ones and try again.
The fan is overheating
If the fan is overheating, unplug it and let it cool down for at least 30 minutes. Check if the air filter is dirty and clean it if necessary. Make sure the fan is not placed in a confined space or near any heat sources.
The fan is making a humming noise
A humming noise is usually caused by a loose belt. Tighten the belt according to the manufacturer’s instructions. If the noise persists, contact Vornado customer service.
The fan is leaking water
If the fan is leaking water, it is likely that the water tank is overfilled. Empty the water tank and refill it to the correct level. Check the rubber gasket on the water tank for any leaks and replace it if necessary.
Safety Precautions
Unplug the device: Always unplug the Vornado fan from the power source before attempting any disassembly or cleaning.
Allow to cool: The fan may still be warm after use. Allow it to cool down completely before handling any parts.
Wear gloves: To prevent cuts or scratches, wear gloves when disassembling the fan.
Use a clean workspace: Choose a clean and well-lit area to work on the fan.
Take photos: Take pictures of the fan’s assembly before taking it apart. This will help you reassemble it correctly later.
Label parts: As you disassemble the fan, label the parts with masking tape or a marker. This will help you keep track of which parts go where.
Avoid using tools: If possible, avoid using any tools to disassemble the fan. However, if necessary, use only a screwdriver or other appropriate tools.
Handle wires carefully: Be careful when handling the fan’s electrical wires. Avoid pulling or cutting them.
Dispose of parts properly: Once you have disassembled the fan, dispose of any broken or damaged parts properly.
Reassemble with care: When reassembling the fan, follow the steps in reverse order. Make sure to tighten all screws and connections securely.
Test before use: Once the fan is reassembled, test it to make sure it is working properly before using it.
How to Take Apart Vornado EH1 00115: A Comprehensive Guide
The Vornado EH1 00115 is a powerful and efficient air circulator that provides optimal air circulation throughout your home. While this appliance is generally durable and reliable, there may come a time when you need to take it apart for maintenance or repairs.
This guide will provide you with step-by-step instructions on how to safely and effectively disassemble the Vornado EH1 00115. By following these instructions, you can maintain the optimal performance of your air circulator and extend its lifespan.
People Also Ask
How do I access the motor of the Vornado EH1 00115?
To access the motor, you will need to remove the fan head and the base. Once you have removed these components, you will see the motor housing. Remove the screws holding the motor housing in place and carefully lift it off. The motor will be located inside the housing.
How do I replace the fan blades on the Vornado EH1 00115?
To replace the fan blades, you will need to remove the fan head. Once you have removed the fan head, you will see the fan blades. Remove the screws holding the fan blades in place and carefully lift them off. Replace the old fan blades with the new ones and secure them with the screws.
